Sony MZ-R910 User Manual
32
B Additional information
Messages
If the recorder cannot carry out an operation,
error messages may flash in the display window
as follows.
error messages may flash in the display window
as follows.
BANK FULL :
The phrase bank is almost full and cannot
store the phrase you tried to enter.Delete
some phrases from the phrase bank, and
then reenter the new phrase.
store the phrase you tried to enter.Delete
some phrases from the phrase bank, and
then reenter the new phrase.
BLANKDISC :
You tried to play an MD with no
recording on it.
recording on it.
BUSY :
You tried to operate the recorder while it
was accessing the recorded data. Wait
until the message goes out (in rare cases,
it may take a few minutes).
was accessing the recorded data. Wait
until the message goes out (in rare cases,
it may take a few minutes).
Data Save :
The MD recorder is recording
information (sounds) from the memory to
the disc. Wait until this process is
completed. Do not expose the recorder to
any physical shock, nor disrupt power
supply.
information (sounds) from the memory to
the disc. Wait until this process is
completed. Do not expose the recorder to
any physical shock, nor disrupt power
supply.
DISC FULL :
There is no more space to record on the
MD.
MD.
EMPTY :
You tried to erase data in the phrase bank
but no data have been recorded.
but no data have been recorded.
Hi DC in :
The power supply is higher than required.
Use the recommended power sources.
Use the recommended power sources.
HOLD :
You tried to operate the recorder with the
HOLD switch slid in the direction of the
arrow. Slide back the switch.
HOLD switch slid in the direction of the
arrow. Slide back the switch.
LINE OUT :
You pressed VOL +/– while the “AUDIO
OUT” parameter is set to “LINE OUT”.
Use the jog dial to set the “AUDIO OUT”
parameter to “HeadPhone”.
OUT” parameter is set to “LINE OUT”.
Use the jog dial to set the “AUDIO OUT”
parameter to “HeadPhone”.
LOW BATT :
The rechargeable battery or dry battery is
weak. Charge the rechargeable battery or
replace the dry battery.
weak. Charge the rechargeable battery or
replace the dry battery.
MEM OVER :
You started recording with the recorder
receiving continuous vibration. Put the
recorder on the stable place and start
recording again.
receiving continuous vibration. Put the
recorder on the stable place and start
recording again.
MENU :
You pressed a key on the remote control
while selecting a menu on the recorder.
while selecting a menu on the recorder.
NAME FULL :
You tried to enter more than 200 letters to
label a single track or disc.
You tried to enter a total of more than
1700 letters for track or disc names.
label a single track or disc.
You tried to enter a total of more than
1700 letters for track or disc names.
NO COPY :
You tried to make a copy from a disc that
is protected by the Serial Copy
Management System. You cannot make
copies from a digitally connected source
which was itself recorded using the digital
connection. Use the analog connection
instead.
is protected by the Serial Copy
Management System. You cannot make
copies from a digitally connected source
which was itself recorded using the digital
connection. Use the analog connection
instead.
NO DISC :
You tried to play or record with no disc in
the recorder.
the recorder.
No Entry! :
You tried to erase a setting in the Personal
Disc Memory on a disc that contains no
settings in the Personal Disc Memory.
Disc Memory on a disc that contains no
settings in the Personal Disc Memory.
NO SIGNAL :
The recorder could not detect digital input
signals. Make sure that the source is
connected firmly. If the message appears
while recording, press x to end recording.
signals. Make sure that the source is
connected firmly. If the message appears
while recording, press x to end recording.
NO TEXT :
You tried to use the CD text copying
function to copy a track or disc name
from a CD that has no text data.
function to copy a track or disc name
from a CD that has no text data.
NV ERROR :
Internal processing was not correctly
done.
Reinsert the disc or try repeating the
recorder operation. If the same message
appears again, a mechanical problem may
be the cause. In this case, consult your
nearest Sony dealer.
done.
Reinsert the disc or try repeating the
recorder operation. If the same message
appears again, a mechanical problem may
be the cause. In this case, consult your
nearest Sony dealer.
P/B ONLY :
You tried to record or edit on a
premastered MD (P/B stands for
playback).
premastered MD (P/B stands for
playback).
PROTECTED :
You tried to record or edit on an MD with
its tab in the record-protect position.
its tab in the record-protect position.