Panasonic MC-CG463 User Manual

4

•  This appliance is not intended for use by young children or infirm person without supervision; young children should be 

supervised to ensure that they do not play with the appliance.

• Do not use the appliance if the mains lead or plug is damaged or faulty.

•  This appliance is provided with a mains lead and if this becomes damaged, it must be repaired by an Authorised Service Centre 

or a qualified person in order to avoid any hazard.

• Unplug from the socket when not in use and before cleaning the appliance or undertaking maintenance operations. 

• Turn off the appliance before removing the plug.  Do not pull on the mains, always pull on the plug body itself.

• Do not handle plug or vacuum cleaner with wet hands.

• Do not use wet filters after wash, make sure they are completely dry to avoid damaging the cleaner.

• Do not vacuum flammable or combustible substances, neither use in areas where they may be present.

• Do not vacuum hot ash, embers or large and sharp objects.

•  Do not vacuum water or other liquids. 

• Keep the vacuum cleaner away from heat sources such as radiators, fires, direct sunlight, etc.

•  This vacuum cleaner is fitted with a thermal cut-out device which automatically turns off the cleaner to prevent overheating of the 

motor. When this happens, disconnect the cleaner from the mains socket and check the dust compartment and filters as they 

may be full or clogged with fine dust. Check for any other obstructions in the hose or tube. After removing the obstruction, leave 

the cleaner to cool down until the thermal cut-out resets after approximately 60 minutes.

A) Turbine nozzle (Only MC-CG467)

B) Ionizer nozzle (Only MC-CG465)

C) Floor nozzle

D) Connection pipe

E) Hose

F) Suction regulator

G) Curved wand

H) Telescopic wand   (MC-CG467)

 (MC-CG465, MC-CG463)

) Extension wand (MC-CG461)

J) Hose inlet

K) Dust indicator

L) Dust cover

M) ON /OFF Switch pedal

N) Cord rewind pedal

O) Crevice nozzle

P) Dusting brush

Q) Exhaust cover

R) Plug

S) Variable power control button

B-1   Insert connection pipe into  hose inlet until it locks. When 

removing hose assembly, pull out connection pipe with 

pushing down two connection buttons.

NOTE:  Do not bend, pull and step on the hose or put 

anything heavy on it.

B-2    Connect the two extension wands by inserting one into 

the other and twisting together. (depending on model)

B-3   Insert the hose unit into the upper end of the connected 

extension wand or telescopic wand and the floor nozzle 

to the other end.

 

(depending on model ).

B-4   Insert the hose unit into the upper end of the telescopic 

wand. Twist the telescopic wand so that the round hole 

will fit into the tab on the hose unit. (When removing the 

hose, push the tab down whilst pulling on the telescopic 

wand)

 

 Attach the Turbine Nozzle to the other end (depending 

on model)( Removal as per reverse procedure)

B-5   You can adjust the length of telescopic wand by pushing 

button. (depending on model)

C-2   Gently press at the centre of the switch pedal to turn 

 

 Press the pedal again to turn it OFF.

 To increase or decrease the power, turn the variable 

power control button.

C-4   Switching between carpet and flooring

 

Flooring: Press lever A

 

Carpet: Press lever B

 

 

Flooring (PARQUET): Set position A

 

Carpet (short): Set position B

 

Carpet (long or hard to push): Set position C

C-5   The curved wand of the hose is attached with a manual 

suction regulator, which allows you to briefly reduce the 

suction level.

C-6   After you finish vacuuming, remove the plug from 

 

 When rewinding the power cord, press the cord rewind 

pedal by holding the plug so that it does not become 

damaged.

C-7  Storage position

 

 Insert  the  wand  holder  straight  into  the  wand 

supporter.

C-8   Park system

 

 For  short  breaks  during  vacuuming,  slide  the  hook 

attached to the nozzle pipe into the slot on the rear side 

of the cleaner.

 

NOTE:  When  you  use  park  position,  we  suggest  the 

appliance is switched off.