Sony MDX-CA680 User Manual
26
Troubleshooting
The following checklist will help you remedy
problems you may encounter with your unit.
Before going through the checklist below, check
the connection and operating procedures.
problems you may encounter with your unit.
Before going through the checklist below, check
the connection and operating procedures.
General
No sound.
• Rotate the volume control dial clockwise to
adjust the volume.
• Cancel the ATT function.
• Set the fader control to the centre position for
• Set the fader control to the centre position for
a 2-speaker system.
The message “LP” appears in the display.
MDLP tracks cannot be played back.
MDLP tracks cannot be played back.
An optional MD unit does not conform to
MDLP playback.
t Use this unit to playback the MDLP tracks.
MDLP playback.
t Use this unit to playback the MDLP tracks.
The contents of the memory have been
erased.
erased.
• The RESET button has been pressed.
t Store again into the memory.
• The power cord or battery has been
disconnected.
• The power connecting cord is not connected
properly.
No beep sound.
The beep sound is cancelled (page 21).
Indications disappear from/do not appear in
the display.
the display.
• The clock display disappears if you press
(OFF) for 2 seconds.
t Press (OFF) again for 2 seconds to
t Press (OFF) again for 2 seconds to
display the clock.
• Remove the front panel and clean the
connectors. See “Cleaning the connectors”
(page 23) for details.
(page 23) for details.
Stored stations and correct time are erased.
The fuse has blown.
Makes noise when the ignition key is in the
ON, ACC, or OFF position.
The fuse has blown.
Makes noise when the ignition key is in the
ON, ACC, or OFF position.
The leads are not matched correctly with the
car’s accessory power connector.
car’s accessory power connector.
No power is being supplied to the unit.
• Check the connection. If everything is in
order, check the fuse.
• The car does not have an ACC position.
t Press (SOURCE) (or insert a disc) to turn
on the unit.
The power is continuously supplied to the
unit.
unit.
The car does not have an ACC position.
The power aerial does not extend.
The power aerial does not have a relay box.
The operation buttons do not function.
Press the RESET button.
CD/MD playback
A disc cannot be loaded.
• Another MD/CD is already loaded.
• The MD/CD is forcibly inserted upside down
• The MD/CD is forcibly inserted upside down
or in the wrong way.
Cannot turn off the “--------” indication.
You entered the name edit mode.
t Press (LIST) for 2 seconds.
t Press (LIST) for 2 seconds.
Playback does not begin.
• Defective MD or dirty CD.
• CD-R that is not finalized.
• You tried to playback a CD-R not designed
• CD-R that is not finalized.
• You tried to playback a CD-R not designed
for audio use.
• Some CD-Rs may not play due to its
recording equipment or the disc condition.
A disc is automatically ejected.
The ambient temperature exceeds 50°C.
The sound skips from vibration.
• The unit is installed at an angle of more than
20°.
• The unit is not installed in a sturdy part of
the car.
The sound skips.
Dirty or defective disc.
Radio reception
Preset tuning is not possible.
• Store the correct frequency in the memory.
• The broadcast signal is too weak.
• The broadcast signal is too weak.
The stations cannot be received.
The sound is hampered by noises.
The sound is hampered by noises.
• Connect a power aerial control lead (blue) or
accessory power supply lead (red) to the
power supply lead of a car’s aerial booster.
(Only when your car has built-in FM/MW/
LW aerial in the rear/side glass.)
power supply lead of a car’s aerial booster.
(Only when your car has built-in FM/MW/
LW aerial in the rear/side glass.)
• Check the connection of the car aerial.
• The auto aerial will not go up.
• The auto aerial will not go up.
t Check the connection of the power aerial
control lead.
• Check the frequency.
Automatic tuning is not possible.
• The local seek mode is set to “ON.”
t Set the local seek mode to “OFF” (page
21).
• The broadcast signal is too weak.
t Perform manual tuning.
The “ST” indication flashes.
• Tune in the frequency accurately.
• The broadcast signal is too weak.
• The broadcast signal is too weak.
t Set to the monaural reception mode (page
21).