Haier ES10V-M2 Leaflet

60

Do not confuse the water inlet and outlet pipes. The wall bearing the water heater shall be strong 

b

d

e

c

a

Front 

view

Side 

view

Cutaway 

view

Rear 

view

(Figure 1)

The safety valve should be connected to the water inlet pipe. Please check carefully if the 

direction is correct after installation. The correct direction of installation is that the arrowhead 

on the safety valve should point to the water heater.
Please connect the drain hose to the safety valve. Connect one end of the hose to the safety 

valve vent and the other end to the sewage drain for fear of indoor contamination. The hose 

can be cut short or extended as necessary. The hose shall be installed as inclined downward.
The heater should work with the safety valve whose rated pressure is 0.80MPa.
During heating, water may drip from the drain hose of the pressure relief hole due to 

expansion and the hole must be left open to the atmosphere. Check safety valve once a 

The pressure relief hole is to be operated regularly to remove lime deposits and to verify that it is not blocked.

enough to endure a weight twice as much as that of a water heater f

 

illed with water. Do not secure it 

by means of adhesive or similar products because the f

 

ixation by such methods is unreliable.

(Figure 3) for installation 

reference only

(Figure 2)

Extended connection line

Wall rack

Expansion

hook

Cold water  inlet

Mixing

valve

Hot water

outlet valve

Cold water

outlet valve

Shower  head

Hot water outlet

Safety valve

Please fasten the drain hose to the pressure relief hole of the safety valve by twisting (see to 

Figure 4). Connect the other end of drain hose to the sewer to avoid polluting the room by 

splashing. When the power is switched on, and the water heater starts operating, there may 

be some water discharged from the pressure relief hole of the safety valve. It is due to the 

water expansion under heating, and is a normal phenomenon. The pressure relief pipe shall 

communicate with the air directly. Do not block it. The drain hose connecting to the safety 

valve shall be kept downward sloping in installation and in a frost-free environment.
Be sure to check and conf

 

irm that the tank is f

 

illed with 

water, there is no leakage at each joint and the power supply 

complies with the stipulation before switching on the power.
This heater must be equipped with the safety valve along 

with the machine; otherwise any safety accident and property 

loss caused thereby shall be the user's own responsibility.

To avoid danger caused by accidental resetting of the heating breaker, the power for the heat 

cannot be supplied by timer and other external switch devices or connected to circuit with 

frequent switching for facility use.
If any part is damaged, please contact the local maintenance agent and have it replaced with 

our spare parts.
 Tap water inlet pressure shall be no less than 0.05MPa and the maximum pressure shall not 

exceed 0.75MPa.

After installation, as the tank is empty in the f

 

irst usage, be sure to open the tap water inlet 

valve and turn to the top temperature button on the mixing valve. When the tank is f

 

illed 

with water, and the shower nozzle or other water outlet keeps the water output, please close 

the mixing valve, check if there is water leakage at each joint and plug the power.
Turn the knob as per the needed water temperature. The setting temperature rises gradually 

when the temperature regulating knob is rotated clockwise; when setting to the maximum 

temperature, the knob cannot be rotated any more; the temperature decreases gradually in 

case of anticlockwise rotation of the knob. The mark of the knob increases from the actual 

temperature to 75

o

C. You can set the heating temperature steplessly. The heating indicator 

will light on under heating mode. Generally, the knob should be set to the highest scale. The 

automatically when the set temperature is reached, and will be switched on automatically when 

the temperature drops to a certain level. As it continues heating, you can use hot water as well.
When the tap water inlet pressure arrives at or exceeds 0.80MPa, the drain hose of safety 

valve will discharge a large amount of water. It is due to extra high water pressure. Please 

contact the local after service agent for disposal.
In long-term out-of-use or maintenance of the heater, you can close the city water pipe valve 

and set the mixing valve to the highest water temperature rate after opening the safety valve 

handle. Move up the safety valve handle to drain the tank. To avoid injury, before the next 

use, it is suggested to f

 

irst open hot water valve before switching on the water heater, exhaust 

gas possibly retained in the pipeline. In this case, no smoke or f

 

ire is permitted near the open 

valve. Carefully check and conf

 

irm all parts are in good condition.

Safety: High quality heatproof stainless steel electric heating element, over-temperature 

protection; overpressure protection of tank; safe and reliable. The third-generation "Safe Care" 

design for safer usage.
Durability: Full plastic shell, handsome and durable. Enamel tank, with reliable quality and 

long operation life.
Convenience: Adjustable water temperature; water inlet adjusting range: actual temperature 

~75

o

C.

Multiple usage: Enclosed structure, capable of supplying water to multiple places like toilet, 

kitchen etc. Suitable for family, enterprises, service trades like beauty care on hot water 

supply (not drinkable).

Disconnect power supply before cleaning. Gently wipe with wet cloth dipped with a little 

mild detergent. Do not use gasoline or other solvents. Finally dry with a dry cloth. Keep 

water heater dry.

 

iciency, heating elements and tank liner of water heater shall be 

cleaned once every three years. Take care not to damage the protection layer on heating 

elements and tank liner surface. According to the local water quality, magnesium rod shall 

be periodically replaced. If maintenance is needed, please contact a local service station.

No water

1 

No water supply or water 

pressure too low

Check

2 

Water use point is blocked or hot 

water valve is closed

Check and clear

Only cold water 

but pointer light 

when heat

1 

Hot water access close

Check and open

2 

Temperature not set to desired 

setting

Adjust the temperature of water

3 

Heating time limit and setting 

temperature not obtained

Keep heating

4 

Defective heater

Contact with service department 

when 1, 2 and  3 are excluded.

Only cold water 

and pointer not lit 

when heated

1 

No power to heater

Check power socket

2 

Uncontrollable thermostat

Contact with service department 

when 1 is excluded.

Heating pointer 

always lit

1 

Setting water temperature not 

obtained

Keep heating

2 

Uncontrollable thermostat

Contact with service department 

when 1 is excluded.

and temperature 

of water

 Inconstant water pressure

with constant water pressure

 

icient hot 

water

1 

Temperature set too low

Adjust setting water temperature

2 

Excessive water pressure

Rated voltage

V 

230

230

230

Rated frequency

Hz

50

50

50

Rated pressure

MPa

0.80

0.80

0.80

Power

W

2000

2000

2000

Net weight

kg

8

10

14

Rated temperature

o

C

75

75

75

Volume

L

10

15

25

Waterproof grade

/

IPX4

IPX4

IPX4

Mixing factor

%

9

11

12

Tap water pressure

MPa No less than 

0.05MPa

No less than 

0.05MPa

No less than 

0.05MPa

Average temperature of hot 

water outlet

o

C

60

60

Re-heating time   

(a temperature rise of 50

o

C) min

18

28

46

Diameter of power wire

mm

2

3×1.5

3×1.5

3×1.5

Nice molding, space-saving: Vertical type wall-mounting design, saving space  

The water heater you purchased is the improved model of the series product. Please operate 

according to the user's manual.

Technical data • Packing list

(Figure 4)

Connect 

to drain 

hose

Model

a

b

c

d

e

ES10V-M1/M2

298mm

287mm

501mm

152mm

100mm

ES15V-M1/M2

318mm

300mm

623mm

152mm

100mm

ES25V-M1/M2

378mm

374mm

616mm

152mm

100mm

A Hot water outlet 

B Cold water inlet  C Tank

 

D Heating element

 

E Anode rod

F  Thermometer tube   G Wall-mounting bracket  H Temperature regulating knob

Remarks: 1.  The permitted error limit of the above parameters is ±10%. 

2.  The thermoter is not a precision temperature meter. The dial is divided into three 

zones which are blue, croci and red, only representing the water temperature of 

the heater tank from low to high.  

Remarks: The permitted error limit of net weight above is ±10%.

ES35V-M1/M2

415mm

405mm

663mm

152mm

100mm

230

50

0.80

2000

75
35

IPX4

No less than 

0.05MPa

3×1.5

60

65

10

16