SouthWing SA505 User Manual

Thank you for choosing a Bluetooth

®

pro-

duct from SouthWing.
This user guide provides all the information
you will need to use and care for your
product.
All relevant information regarding your
SouthWing product can be found on the
support section of our website: 
www.south-wing.com

You will need to charge the battery of your
Headset. To do so, follow these steps:
1. Make sure the Headset are turned off
2. Plug the power supply into a power point
3. Plug the connector of the power supply
into the USB Charging Socket [1]. The
Charging Light [3] will turn orange to indi-
cate the Headphone battery is charging
4. Once the Charging Light [3] turns off, the
Headset are fully charged and can be
removed from the power supply

Thanks to its USB charging facility, the
Headset battery can be charged from any
USB port, such as those found on a PC or
laptop, by using the SouthWing USB cable
adaptor accessory.

Please Note:
· The Headset will not function while charging.
· If the Charging Light [3] remains off when charging,

the battery is already fully charged and does not
require further charging. 

· To maximise battery life, do not charge the Headset

for extended periods of time.

· Full battery capacity will be achieved after two or

three full charge/discharge cycles.

· When your battery is flat, it takes up to three hours

to completely charge your Headset

· Only use SouthWing power supply or accessories

for charging.

Before turning the Headset on, make sure the
microphone is in the up position as in Figure 2.
To turn the Headset on, move the Power
switch [2] to the ON position. A short tone
will be heard and the Status Light [10] will
start flashing slowly in red. When the
Headset is turned on, it will automatically
connect to the last phone and stereo music
devices that were connected.
To turn the Headset off, move the Power
switch [2] to the OFF position.

For added convenience, your Headset has
an auto-pairing function so that when you
turn the Headset on for the first time, it is
already in pairing mode. The Status Light
[10] will flash blue and red alternately and 2
short tones will be heard. Then, follow
these steps:
1. Put the other Bluetooth device into pair-
ing mode (see the instructions which came
with your device). Ensure that the Bluetooth
device is no more than 1 metre away from
the Headset.
2. Enter the PIN number: 0000. If pairing is
successful, the Status Light [10] will flash
slowly in red.

You will need to follow the steps below if
you want to pair your Headset with another
Bluetooth device. Your Headset will store
the pairings of 5 devices. You may pair to
more devices, but each new device will
replace a previously paired device.
1. Press and hold the Play Button [7] for
about 5 seconds until the Status Light [10]
flashes blue and red alternately and 2 short
tones are heard
2. Then complete normal pairing process
by following points 1 and 2 of the auto-pair-
ing section above.

2

3

The SA505 is compatible with Bluetooth enabled
mobile phones; Bluetooth enabled music players
and Bluetooth USB and audio adapters (dongles).
All of these will be referred to in this guide as
“Bluetooth device”.

Please read the “Safe Usage Guidelines” and 
“Limited Warranty” before using the Headset.

USER GUIDE

SA505

Bluetooth

®

Wireless Headset 

Introduction  ........................................................................................................................... 3

1. Charging the Headset ............................................................................................................ 3

2. Turning the Headset on and off ............................................................................................ 3

3. Pairing the Headset ............................................................................................................. 3-4

4. General Usage  .................................................................................................................... 4-5

5. Push4

TM

call  ............................................................................................................................ 5

6. Additional Functions .............................................................................................................. 5

7. Troubleshooting  ..................................................................................................................... 6

8. Additional Information ........................................................................................................ 6-7

9. Declaration of Conformity  ..................................................................................................... 8

10. Command Summary ............................................................................................................ 9

® Bluetooth is a registered trademark owned by Bluetooth SIG, Inc. U.S.A. and licensed to SouthWing.