Sony PDW-HD1500 User Manual
42
Handling Discs
Ch
apt
apt
er 3 Prep
ar
at
ion
s
s
P5 REF page
P6 OTHER page
Handling Discs
Discs used for recording and
playback
playback
This unit can record and play back the following
Professional Disc
Professional Disc
1)
formats.
• PFD23A (capacity 23.3 GB)
• PFD50DLA (capacity 50.0 GB)
• PFD50DLA (capacity 50.0 GB)
1) Professional Disc is a trademark of Sony Corporation.
• It is not possible to use the following discs for recording
or playback:
-Blu-ray Disc
-Professional Disc for Data
-Blu-ray Disc
-Professional Disc for Data
• PFD50DLA discs can be used only by XDCAM devices
with the DL mark (see the following illustration). They
cannot be used by XDCAM devices without this mark.
cannot be used by XDCAM devices without this mark.
Notes on handling
Handling
The Professional Disc is housed in a cartridge, and is
designed to allow handling free of risk from dust or
fingerprints. However, if the cartridge is subjected to a
severe shock, for example by dropping it, this can result in
damage or scratching of the disc. If the disc is scratched, it
may be impossible to record video/audio, or to play back
the content recorded on the disc. The discs should be
handled and stored carefully.
• Do not touch the surface of the disc itself within the
The Professional Disc is housed in a cartridge, and is
designed to allow handling free of risk from dust or
fingerprints. However, if the cartridge is subjected to a
severe shock, for example by dropping it, this can result in
damage or scratching of the disc. If the disc is scratched, it
may be impossible to record video/audio, or to play back
the content recorded on the disc. The discs should be
handled and stored carefully.
• Do not touch the surface of the disc itself within the
cartridge.
• Deliberately opening the shutter may cause damage.
• Do not disassemble the cartridge.
• The supplied adhesive labels are recommended for
• Do not disassemble the cartridge.
• The supplied adhesive labels are recommended for
indexing discs. Apply the label in the correct position.
Storage
• Do not store discs where they may be subjected to direct
• Do not store discs where they may be subjected to direct
sunlight, or in other places where the temperature or
humidity is high.
humidity is high.
• Do not leave cartridges where dust may get inside.
• Store cartridges in their cases.
• Store cartridges in their cases.
Care of the discs
• Remove dust and dirt on the outside of a cartridge using
• Remove dust and dirt on the outside of a cartridge using
a soft dry cloth.
Item
Setting
F1: OUT REF
Selects the reference signal for the
output signals of this unit.
REF: Use the signal input to the
output signals of this unit.
REF: Use the signal input to the
REF.VIDEO INPUT connector as the
output reference signal.
output reference signal.
INPUT: Use the input video signal as the
output reference signal.
F2:
(Unassigned function button)
F3:
(Unassigned function button)
F4:
(Unassigned function button)
F5: SYNC
Sets the sync phase of HD output
signals. While the setting value is
flashing, turn the PUSH SET(S.SEL)
knob to adjust the sync phase of output
signals with respect to the input
reference signal, over the range ±15 µs.
(The display shows –128 to +127.)
signals. While the setting value is
flashing, turn the PUSH SET(S.SEL)
knob to adjust the sync phase of output
signals with respect to the input
reference signal, over the range ±15 µs.
(The display shows –128 to +127.)
F6: FINE
Makes fine adjustment to the sync phase
of HD output signals. While the setting
value is flashing, turn the PUSH
SET(S.SEL) knob to adjust the sync
phase of output signals with respect to
the input reference signal, over the range
±200 ns. (The display shows 0 to 1023.)
of HD output signals. While the setting
value is flashing, turn the PUSH
SET(S.SEL) knob to adjust the sync
phase of output signals with respect to
the input reference signal, over the range
±200 ns. (The display shows 0 to 1023.)
Item
Setting
F1: CONV IMP
Selects whether to display convert status
on the display during downconvert
operations.
OFF: Do not display.
ON: Display.
on the display during downconvert
operations.
OFF: Do not display.
ON: Display.
F2: ERR LOG
Displays an error log screen.
F3:
(Unassigned function button)
F4:
(Unassigned function button)
F5:
(Unassigned function button)
F6:
(Unassigned function button)
Notes
DL mark