Kingston Technology 16GB DDR3 240-pin DIMM Kit KVR1066D3Q4R7S/16G Data Sheet
Product codes
KVR1066D3Q4R7S/16G
Memory Module Specifications
KVR1066D3Q4R7S/16G
16GB 2048M x 72-Bit PC3-8500
CL7 Registered w/Parity 240-Pin DIMM
CL7 Registered w/Parity 240-Pin DIMM
Kingston.com
Document No. VALUERAM0921-001.A00 06/07/10 Page 1
DESCRIPTION
This document describes ValueRAM’s 2048M x 72-bit (16GB)
DDR3-1066 CL7 SDRAM (Synchronous DRAM) registered w/
parity, quad-rank memory module. The module is based on thirty-
six DDP (Dual Die Package) 1Gb x 4-Bit 1066MHz SDRAMs. The
SPD is programmed to JEDEC standard latency 1066MHz timing
of 7-7-7 at 1.5V. This 240-pin DIMM uses gold contact fingers
and requires +1.5V. The electrical and mechanical specifications
are as follows:
DDR3-1066 CL7 SDRAM (Synchronous DRAM) registered w/
parity, quad-rank memory module. The module is based on thirty-
six DDP (Dual Die Package) 1Gb x 4-Bit 1066MHz SDRAMs. The
SPD is programmed to JEDEC standard latency 1066MHz timing
of 7-7-7 at 1.5V. This 240-pin DIMM uses gold contact fingers
and requires +1.5V. The electrical and mechanical specifications
are as follows:
FEATURES
• JEDEC standard 1.5V ± 0.075V Power Supply
• VDDQ = 1.5V ± 0.075V
• 533MHz fCK for 1066Mb/sec/pin
• 8 independent internal bank
• Programmable CAS Latency: 6,7,8
• Programmable Additive Latency: 0, CL - 2, or CL - 1 clock
• Programmable CAS Write Latency(CWL) = 6(DDR3-1066)
• 8-bit pre-fetch
• Burst Length: 8 (Interleave without any limit, sequential with
• VDDQ = 1.5V ± 0.075V
• 533MHz fCK for 1066Mb/sec/pin
• 8 independent internal bank
• Programmable CAS Latency: 6,7,8
• Programmable Additive Latency: 0, CL - 2, or CL - 1 clock
• Programmable CAS Write Latency(CWL) = 6(DDR3-1066)
• 8-bit pre-fetch
• Burst Length: 8 (Interleave without any limit, sequential with
starting address “000” only), 4 with tCCD = 4 which does
not allow seamless read or write [either on the fly using A12
or MRS]
not allow seamless read or write [either on the fly using A12
or MRS]
• Bi-directional Differential Data Strobe
• Internal(self) calibration : Internal self calibration through ZQ
• Internal(self) calibration : Internal self calibration through ZQ
pin (RZQ : 240 ohm ± 1%)
• On Die Termination using ODT pin
• On-DIMM thermal sensor (Grade B)
• Average Refresh Period 7.8us at lower than TCASE 85°C,
• On-DIMM thermal sensor (Grade B)
• Average Refresh Period 7.8us at lower than TCASE 85°C,
3.9us at 85°C < TCASE ≤ 95°C
• Asynchronous Reset
• PCB : Height 30.00mm, double sided component, w/ Full
• PCB : Height 30.00mm, double sided component, w/ Full
DIMM Heat Spreader
SPECIFICATIONS
CL(IDD)
7 cycles
Row Cycle Time (tRCmin)
50.625ns (min.)
Refresh to Active/Refresh
160ns (min.)
Command Time (tRFCmin)
Row Active Time (tRASmin)
37.5ns (min.)
Power
6.222 W (operating)
UL Rating
94 V - 0
Continued >>