Philips AX5116 User Manual

You can store up to 30 tracks to play in a program.
A single track may be stored more than once in the 
program.

1 While playback is stopped, select a track with

∞ or §.

2 Press PROGRAM to store the track.

yprogram lights up; the track number 

programmed and P with the total number of

stored tracks are displayed.

3 Select and store all desired tracks in this way.

4 Press 

2; to start playback of your selected tracks.

yprogram is shown and playback starts.

• You can review the program by pressing PROGRAM 

for more than 2 seconds.

yThe display shows all the stored tracks in sequence.

Notes: – If you press PROGRAM and there is no track selected, SEL is 

displayed.

– If you try to store more than 30 tracks, FULL is displayed.

Clearing the program
• While playback is stopped, press 

9 to clear program.

yCLr is displayed once, program goes off,

and the program is cleared.

Note:

The program will also be cleared if the power supply is interrupted, or if
the CD-player lid is opened, or if the set switches off automatically.

You can interrupt playback and continue (even after an 
extended period of time) from the position where 
playback stopped (RESUME) and you can lock all buttons
of the set so that no action will be executed (HOLD).
Use the RESUME–HOLD–OFF slider for these functions.

RESUME – continuing from where you have stopped
1 Switch the slider to RESUME during playback to activate RESUME.

yresume is shown.

2 Press 

9 whenever you want to stop playback.

3 Press 

2; whenever you want to resume playback.

yresume is shown and playback continues

from where you have stopped.

• To deactivate RESUME, switch the slider to OFF.

yresume goes off.

HOLD – locking all buttons
You can lock the buttons of the set by switching the slider to HOLD. Now, when a
key is pressed, no action will be executed. This is of use, for example, when
transporting the player in a bag. With HOLD activated, you can avoid accidental
activation of other functions.

1 Switch the slider to HOLD to activate HOLD.

yAll buttons are locked. HoLd is shown when

you press any button. If the set is switched off,
hold will be shown only when 

2; is pressed.

2 To deactivate HOLD, switch the slider to OFF.

Note: If you deactivate HOLD by switching the slider to RESUME, you will be acti-

vating the RESUME function.

WARNING: Under no circumstances should you try to repair the set yourself as
this will invalidate the warranty. If a fault occurs, first check the points listed,
before taking the unit for repair. If you are unable to solve a problem by following
these hints, consult your dealer or service center.

The CD player has no power, or playback does not start
• Check that your batteries are not dead or empty, that they are inserted 

correctly, that the contact pins are clean.

• Your adapter connection may be loose. Connect it securely.
•

For in-car use, check that the car ignition is on. Also check player’s batteries.

The indication no diSC is displayed
• Check that the CD is clean and correctly inserted (label-side upward).
• If your lens has steamed up, wait a few minutes for this to clear.

The indication nF diSC is displayed
• CD-RW (CD-R) was not recorded properly. Use FINALIZE on your CD-recorder.

• If HOLD is activated, then deactivate it.
• Electrostatic discharge. Disconnect power or remove batteries for a few seconds.

The CD skips tracks
• The CD is damaged or dirty. Replace or clean the CD.
• RESUME, SHUFFLE or PROGRAM is active. Switch off whichever is on.

No sound or bad sound quality.
• PAUSE might be active. Press 

2;.

• Loose, wrong or dirty connections. Check and clean connections.
• Volume might not be appropriately adjusted. Adjust the volume.
• Strong magnetic fields. Check player’s position and connections. Also keep

away from active mobile phones.

•

For in-car use, check that the cassette adapter is inserted correctly, that the car
cassette player’s playback direction is correct (press autoreverse to change),
and that the cigarette lighter jack is clean. Allow time for temperature change.

It is possible to play tracks in random order, to repeat a
single track or the entire CD, and to play the first few
seconds of each track.
1 Press MODE during playback as often as required in

order to activate one of the following ‘modes’. The
active mode is shown in the display.

yshuffle : All tracks of the CD are played in 

random order until all of them have been played once.

yshuffle repeat all : All tracks of the CD

are played repeatedly in random order.

yrepeat : The current track is played repeatedly.
yrepeat all : The entire CD is played repeatedly.

y SCAN: The first 10 seconds of each of the

remaining tracks are played in sequence.

2 Playback starts in the chosen mode after 2 seconds.

• To return to normal playback, press MODE repeatedly until the display shows

no active modes.

With a conventional portable CD-player you might have experienced that the
music stopped e.g. when you were jogging. The Electronic Skip Protection 
prevents loss of sound caused by light vibrations and shocks. Continuous playback
is ensured. However ESP does not prevent playback interruptions during vigorous
running. It also does not protect the unit against any damage caused by dropping!
In this set ESP is default ON. It is possible to set ESP off.
and enter the Power Save Mode.(PS). PS helps to extend
battery lifetime for longer playback.
• Press MODE for more than 2 seconds.

y

disappears.

• Press MODE again for more than 2 seconds.

yPS is displayed once 
ESP on

➟

➟

➟

A

A

PRO

GR

AM

MO

DE

TR

AC

K

MO

DE

program

program

program

−

PRO

GR

AM

MO

DE

TR

AC

K

MO

DE

shuffle repeat all

resume

resume

hold