Sony TCM-AP10 User Manual
Tape counter
While the upper side of the tape is running, the numbers in the tape counter increase.
While the reverse side is running, they decrease. Press the reset button of the TAPE
COUNTER to return to 000.
While the reverse side is running, they decrease. Press the reset button of the TAPE
COUNTER to return to 000.
VOR (Voice Operated Recording)
Set VOR to L or H. Press
r REC, and the unit automatically starts recording the sound
and pauses when there is no sound (you can save tapes and batteries).
H: To record at meetings or in a quiet place.
L: To record for dictation in a noisy place.
When you use this system in a noisy place the unit stays in the recording mode. If the
sound is too soft, on the contrary, the unit will not start recording. Set VOR to L (low)
or H (high) depending on the conditions. When you do not use this function, set VOR
to OFF.
H: To record at meetings or in a quiet place.
L: To record for dictation in a noisy place.
When you use this system in a noisy place the unit stays in the recording mode. If the
sound is too soft, on the contrary, the unit will not start recording. Set VOR to L (low)
or H (high) depending on the conditions. When you do not use this function, set VOR
to OFF.
Notes
• The VOR system depends on the environment conditions. If you cannot get the desired results, set
VOR to OFF.
• When using the VOR system, the unit starts recording only when a sound is detected, therefore,
the beginning of the word may not be recorded. For an important recording, we recommend
setting VOR to OFF.
setting VOR to OFF.
To monitor the sound
Connect an earphone (not supplied) firmly to the EAR jack. The sound for monitoring
can be adjusted by VOL. The recording sound is fixed.
can be adjusted by VOL. The recording sound is fixed.
Start recording during playback
Press
r REC during playback, recording starts immediately. It is useful when you
want to re-record the portion which was just recorded.
Review the portion just recorded
Press REW/REVIEW during recording. Release the button at the point to start
playback.
playback.
DPC (Digital Pitch Control) and Speed
Control Function E
Control Function E
How to adjust the pitch combined with the tape playback speed
Set the DPC switch to AUTO.
Adjust SPEED CONTROL as follows:
Adjust SPEED CONTROL as follows:
To play back
Set SPEED CONTROL to
slower
SLOW
at normal speed
Center
faster
FAST
How to adjust the pitch and the tape playback speed separately
Set the DPC switch to MANUAL.
Use the DPC switch and the PITCH CONTROL switch.
You can make the sound more comprehensible by changing the tape speed.
Use the DPC switch and the PITCH CONTROL switch.
You can make the sound more comprehensible by changing the tape speed.
To play back
Set SPEED CONTROL to
slower
SLOW
at normal speed
Center
faster
FAST
To adjust the pitch
Set PITCH CONTROL to
lower
LOW
normal
Center
higher
HIGH
Notes
• The sound is interrupted for a moment when you change the DPC switch during playback.
• Even though you use the DPC switch, you cannot acquire the same pitch as the original. The tone
• Even though you use the DPC switch, you cannot acquire the same pitch as the original. The tone
will be somewhat different from the original.
• When the power of the batteries becomes weak, SPEED CONTROL may stop if you turn it fast. In
this case turn it slowly or change the batteries.
• When SPEED CONTROL is turned or the volume is adjusted during playback, BATT/REC lamps
may flicker.
Recording from Various Sound Sources
You can monitor the recording sound by connecting an earphone (not supplied).
Use VOR system depending on the environment condition.
Use VOR system depending on the environment condition.
Notes (Before recording)
• When connecting cords, be sure you connect plugs firmly.
• Make a trial recording to make sure that you made connections correctly and adjusted the volume
• Make a trial recording to make sure that you made connections correctly and adjusted the volume
properly.
• The following examples use Sony products. If you have any problem when using other products,
read the instruction manual of those products.
Recording with an External Microphone F-a
Connect a microphone to the MIC jack. There is a small projection to show the position
of the MIC jack near the jack. The built-in microphone will be disconnected and the
sound through the external microphone will be recorded.
When using a plug-in-power system microphone, the power to the microphone is
supplied from this unit.
of the MIC jack near the jack. The built-in microphone will be disconnected and the
sound through the external microphone will be recorded.
When using a plug-in-power system microphone, the power to the microphone is
supplied from this unit.
To start recording, insert a cassette and press
r REC.
Recording from Another Equipment F-b
Connect another equipment to the MIC jack using the RK-G64HG connecting cord (not
supplied).
supplied).
1
Insert a cassette.
2
Adjust the sound of the connected equipment.
3
Press
r REC.
z
Additional Information
Precautions
On power
Operate the unit only on 3V DC. For AC operation, use the AC power adaptor
recommended for the unit. Do not use any other type. For battery operation, use two
size AA (R6) batteries.
recommended for the unit. Do not use any other type. For battery operation, use two
size AA (R6) batteries.
On the unit
• Do not leave the unit in a location near heat sources, or in a place subject to direct
sunlight, excessive dust or mechanical shock.
• Should any solid object or liquid fall into the unit, remove the batteries or disconnect
the AC power adaptor, and have the unit checked by qualified personnel before
operating it any further.
operating it any further.
• If the unit has not been used for a long time, set it in the playback mode and warm it
up for a few minutes before inserting a tape.
Keep personal credit cards using magnetic coding or spring-wound watches etc. away
from the unit to prevent possible damage from the magnet used for the speaker.
from the unit to prevent possible damage from the magnet used for the speaker.
On tapes longer than 90 minutes
We do not recommend the use of tapes longer than 90 minutes except for a long
continuous recording or playback. They are very thin and tend to be stretched easily.
continuous recording or playback. They are very thin and tend to be stretched easily.
If you have any questions or problems concerning your unit, please consult your
nearest Sony dealer.
nearest Sony dealer.
Troubleshooting
Should any problem persist after you have made these checks, consult your nearest
Sony dealer.
Sony dealer.
You cannot insert the cassette.
m
The cassette is inserted front side back.
m
PLAY is pressed.
You cannot close the cassette compartment lid.
m
The cassette is inserted into the wrong part (it should be inserted into the lid
side).
side).
Playback is not possible even if you press PLAY
m
The tape has reached the end. Rewind the tape.
m
The batteries are weak. Replace both batteries with new ones.
You cannot press
r REC.
m
There is no cassette.
m
The tab on the tape has been removed. To reuse the tape for recording, cover
the tab hole with adhesive tape.
the tab hole with adhesive tape.
Recording cannot be made.
m
The batteries are weak. Replace both batteries with new ones.
m
The record/playback head is contaminated.
m
VOR has been set to the improper position when VOR function works.
m
Connection is made incorrectly.
During CUE/REVIEW the tape stops or does not run.
You cannot fast-forward or rewind.
You cannot fast-forward or rewind.
m
The batteries are weak. Replace both batteries with new ones.
The unit does not operate.
m
The batteries have been inserted with incorrect polarity.
m
The batteries are weak. Replace both batteries with new ones.
m
PAUSE c is slid in the direction of the arrow.
m
The AC power adaptor or car battery cord is not firmly connected.
m
The batteries have been inserted, but simultaneously the AC power adaptor is
connected and not to be done to the wall outlet.
connected and not to be done to the wall outlet.
No sound comes from the speaker.
m
The earphone is plugged in.
m
The volume is turned down completely.
Tape speed is too fast or too slow in the playback mode.
m
SPEED CONTROL is set at a point other than the center.
m
DPC is set to AUTO or MANUAL.
The pitch of the sound is different from the original.
m
DPC is active.
m
PITCH CONTROL is set at a point other than the center. (The pitch cannot be
the same as the original.)
the same as the original.)
The sound drops out, sound quality becomes worse or sound
has excessive noise.
has excessive noise.
m
The volume is turned down completely.
m
The batteries are weak. Replace both batteries with new ones.
m
The record/playback head is contaminated.
m
The tone will be somewhat different even though you adjust the pitch. This is
not a malfunction.
not a malfunction.
m
When you adjust the pitch, you sometimes hear buzzing or echoing. This is
caused by the digital processing and is not a malfunction.
caused by the digital processing and is not a malfunction.
m
If the cassette has been put on a speaker without its case, the sound quality
may be distorted.
may be distorted.
m
CrO
2
(TYPE II) or metal (TYPE IV) tape is used.
Recording is interrupted.
m
VOR is set to L or H. When you do not use VOR, set it to OFF.
Recording cannot be erased completely.
m
The erase head is contaminated.
The tape speed cannot be changed even if SPEED CONTROL is
turned.
turned.
m
DPC is set to OFF.
The pitch cannot be changed even if PITCH CONTROL is turned.
m
DPC is set to OFF or AUTO.