Everpure ENVI-RO User Manual

Printed in U.S.A. 

EV3128-25 Rev A   SE08 

The Everpure ENVI-RO™ Mineral Reduction System is a pre-

engineered, pre-assembled Reverse Osmosis (RO) system designed 

to provide high purity water for multiple applications, such as 

premium espresso, coffee, blended beverages and steam, to name a 

few. It combines a number of water treatment technologies into one 

easy to install package. The system provides superior protection 

against taste and odor causing contaminants while removing dirt, 

particulates and dissolved solids that can foul or scale equipment.

Water production depends on supply water pressure and temperature. 

See PERFORMANCE section (page 8) for normalized production.

The following table lists the allowable operating range of various 

water properties within which the ENVI-RO™ will function  

properly.

Total Dissolved Solids (TDS)

0-1,000 ppm (0-1,000 mg/I)

pH

5-10

Chlorine

1

0-3 ppm (0-3 mg/I)

Chloramines

0-3 ppm (0-3 mg/I)

Turbidity

0-1 NTU

Iron

0-1 ppm (0-1 mg/I)

1

 Reverse osmosis membrane filter used in this system will be damaged by chlorine. An 

activated carbon filter should be provided with this system to protect the reverse osmosis 
membrane from chlorine attack. Influent chlorine should not exceed 3 mg/I.

2SR-BW Water Conditioning cartridge

1. 

Dual-Head booster pump

2. 

MR-600 Reverse Osmosis (RO) membrane cartridge.

3. 

6-Gallon RO Water Storage Tank

4. 

Control System with Power Supply

5. 
The 2SR-BW Water Conditioning cartridge contains media that 

reduces the scaling tendency of hard water minerals found in many 

water supplies, extending RO membrane life. 
The Dual-Head booster pump increases the inlet pressure to 

maintain consistent permeate production, plus eliminates back-

pressure on the permeate output. This innovative approach to both 

boosting and eliminating back-pressure allows for maximum system 

efficiency. 
The MR-600 RO membrane cartridge contains a semi-permeable 

reverse osmosis membrane. Here, most dissolved impurities are 

separated from the water and flushed down the drain. The water 

that is able to pass through the membrane, which is very low in 

dissolved impurities, is referred to as permeate, RO water, or 

product water. 
Once the RO water is produced, it is stored in the 6-Gallon RO Water 

Storage Tank. This tank serves two key functions; 1) It acts as a 

buffer between the system and the connected equipment, providing 

ample volumes of water instantaneously, 2) It reduces the on-off 

cycling of the RO system, which  produces better quality water, and 

prolongs the system’s life. 

Dynamic Operating Pressure: 25-80 psi (1.7-5.5 bar)

•

Static Operating Pressure: 100 psi (6.9 bar)

•

Operating Temperature 40-100°F (4.4-37.8°C)

•

Connections

•

Inlet/Outlet: 3/8-inch OD tube (John Guest© Push-in)  

Concentrate: 3/8-inch OD tube (John Guest© Push-in)  

Electrical: 115 volt AC / 60 Hz / 1 Phase

Ampere: 

  Stand-by:   0.2

  Flush: 

0.5

  Run/Fill: 

2.7

Branch Circuit Protection: 15 or 20 AMP Ground Fault Protected

Can

1. 

 the unit be mounted within a reasonable distance of the 

water supply and drain facilities?
Is 

2. 

there an un-switched 115 VAC GFIC (ground fault interrupter 

circuit) protected receptacle available for powering the system?
Is 

3. 

there adequate clearance and support to install the unit 

and permit access for maintenance? The total system weight 

will vary based on model and storage tank selected. See 

specification table for approximate operating weights.
Doe

4. 

s the inlet water supply meet the requirements listed below? 

A minimum of 25 PSI pressure on a consistent basis

a. 

Less than 1,000 ppm of Total Dissolved Solids (TDS)

b. 

pH level between 7.0-9.0

c. 

Turbidity less than 1 NTU

d.