Yamaha RX-V620RDS User Manual
19
English
INTR
ODUCTION
PREP
ARA
TION
B
ASIC
OPERAIONT
AD
V
ANCED
OPERA
TION
ADDITIONAL
INFORMA
TION
APPENDIX
CONNECTIONS
SWITCHED
100W MAX. TOTAL
AC OUTLETS
IMPEDANCE SELECTOR
SET BEFORE POWER ON
MAIN A OR B: 4
MIN. /SPEAKER
A + B: 8
MIN. /SPEAKER
CENTER : 6
MIN. /SPEAKER
REAR : 6
MIN. /SPEAKER
MAIN A OR B: 8
MIN. /SPEAKER
A + B:16
MIN. /SPEAKER
CENTER : 8
MIN. /SPEAKER
REAR : 8
MIN. /SPEAKER
MAINS
IMPEDANCE SELECTOR Switch
WARNING
Do not change the IMPEDANCE SELECTOR switch setting while the power of this unit is on, otherwise the unit
may be damaged.
If this unit fails to turn on when STANDBY/ON (or POWER) is pressed, the IMPEDANCE SELECTOR switch may
not be fully slid to either position. If so, slide the switch to either position fully when this unit is in the standby
mode.
Do not change the IMPEDANCE SELECTOR switch setting while the power of this unit is on, otherwise the unit
may be damaged.
If this unit fails to turn on when STANDBY/ON (or POWER) is pressed, the IMPEDANCE SELECTOR switch may
not be fully slid to either position. If so, slide the switch to either position fully when this unit is in the standby
mode.
Select the left or right position according to the impedance of the speakers in your system. Be sure to move this switch
only when this unit is in the standby mode.
only when this unit is in the standby mode.
Switch
position
position
Speaker
Impedance level
Main
If you use one set of main speakers, the impedance of
each speaker must be 4
each speaker must be 4
Ω or higher.
If you use two sets of main speakers, the impedance of
each speaker must be 8
each speaker must be 8
Ω or higher.
Center
The impedance must be 6
Ω or higher.
Rear
The impedance of each speaker must be 6
Ω or higher.
Right
Main
If you use one set of main speakers, the impedance of
each speaker must be 8
each speaker must be 8
Ω or higher.
If you use two sets of main speakers, the impedance of
each speaker must be 16
each speaker must be 16
Ω or higher.
Center
The impedance must be 8
Ω or higher.
Rear
The impedance of each speaker must be 8
Ω or higher.
Left
Connecting the Power Supply Cords
After completing all connections, connect the AC power cord to an AC power outlet. Disconnect the AC power cord if
you will not use this unit for a long period of time.
you will not use this unit for a long period of time.
■ AC OUTLET(S) (SWITCHED)
Europe model ............................................... 2 OUTLETS
U.K. model ..................................................... 1 OUTLET
Use these outlets to connect the power cords only from
your audio/video components to this unit. The power to
the AC OUTLET(S) is controlled by this unit’s
STANDBY/ON (or POWER and STANDBY). These
outlets will supply power to any connected component
whenever this unit is turned on. The maximum power
(total power consumption of components) that can be
connected to the AC OUTLET(S) is 100 W.
U.K. model ..................................................... 1 OUTLET
Use these outlets to connect the power cords only from
your audio/video components to this unit. The power to
the AC OUTLET(S) is controlled by this unit’s
STANDBY/ON (or POWER and STANDBY). These
outlets will supply power to any connected component
whenever this unit is turned on. The maximum power
(total power consumption of components) that can be
connected to the AC OUTLET(S) is 100 W.
SWITCHED
100W MAX. TOTAL
AC OUTLETS
IMPEDANCE SELECTOR
SET BEFORE POWER ON
MAIN A OR B: 4
MIN. /SPEAKER
A + B: 8
MIN. /SPEAKER
CENTER : 6
MIN. /SPEAKER
REAR : 6
MIN. /SPEAKER
MAIN A OR B: 8
MIN. /SPEAKER
A + B:16
MIN. /SPEAKER
CENTER : 8
MIN. /SPEAKER
REAR : 8
MIN. /SPEAKER
MAINS
(Europe model)
(Europe model)
IMPEDANCE SELECTOR
To AC outlet
SWITCHED
0104V620RDS_19-23_EN
1/18/1, 7:25 PM
19