Yamaha RX-V475 User Manual
APPENDIX
➤ Troubleshooting
En
92
Audio
Problem
Cause
Remedy
No sound.
Another input source is selected.
Select an appropriate input source with the input selection keys.
Signals that the unit cannot reproduce are being input.
Some digital audio formats cannot be played back on the unit. To check the audio
format of the input signal, use “Signal Info” in the “Option” menu (p.66).
format of the input signal, use “Signal Info” in the “Option” menu (p.66).
(RX-V575 only)
Audio output to Zone A (or Zone B) is disabled.
Audio output to Zone A (or Zone B) is disabled.
Press ZONE A (ZONE B) to enable audio output to Zone A (or Zone B).
The cable connecting the unit and playback device is defective.
If there is no problem with the connection, replace with another cable.
The volume cannot be increased.
The maximum volume is set.
Use “Max Volume” in the “Setup” menu to adjust the maximum volume (p.77).
A device connected to the output jacks of the unit is not turned on.
(This may happen due to the nature of AV receivers.)
(This may happen due to the nature of AV receivers.)
Turn on all devices connected to the output jacks of the unit.
No sound is coming from a specific speaker.
The playback source does not contain a signal for the channel.
To check it, use “Signal Info” in the “Option” menu (p.66).
The currently selected sound program/decoder does not use the
speaker.
speaker.
To check it, use “Test Tone” in the “Setup” menu (p.73).
Audio output of the speaker is disabled.
Perform YPAO (p.31) or use “Configuration” in the “Setup” menu to change the
speaker settings (p.71).
speaker settings (p.71).
The volume of the speaker is set too low.
(RX-V575 only)
Audio output to Zone A (or Zone B) is disabled.
Audio output to Zone A (or Zone B) is disabled.
Press ZONE A (ZONE B) to enable audio output to Zone A (or Zone B).
The speaker cable connecting the unit and the speaker is
defective.
defective.
If there is no problem with the connection, replace with another speaker cable.
The speaker is malfunctioning.
To check it, replace with another speaker. If the problem persists, the unit may be
malfunctioning.
malfunctioning.
(RX-V575 only)
No sound is coming from the surround back
speaker.
No sound is coming from the surround back
speaker.
The extended surround is disabled.
Use “Extended Surround” in the “Option” menu to select a decoder to be used
(p.65).
(p.65).
“Power Amp Assign” is set to “BI-AMP” or “Zone B”.
When “Power Amp Assign” in the “Setup” menu is set to “BI-AMP” or “Zone B”,
you cannot use the surround back speakers. To use the surround back speakers,
set “Power Amp Assign” to “Basic” (p.71).
you cannot use the surround back speakers. To use the surround back speakers,
set “Power Amp Assign” to “Basic” (p.71).
No sound is coming from the subwoofer.
The playback source does not contain LFE or low-frequency
signals.
signals.
To check it, set “Extra Bass” in the “Setup” menu to “On”, in order to output the
front channel low-frequency components from the subwoofer (p.72).
front channel low-frequency components from the subwoofer (p.72).
Subwoofer output is disabled.
Perform YPAO (p.31) or set “Subwoofer” in the “Setup” menu to “Use” (p.71).
The volume of the subwoofer is too low.
Adjust the volume on the subwoofer.
The subwoofer has been turned off by its auto-standby function.
Disable the auto-standby function of the subwoofer or adjust its sensitivity level.