Yamaha RX-Z7 User Manual

Page of 178
63
 En
XM® Satellite Radio tuning
BA
S
IC
 
OPERA
T
ION
■ Preset Search mode
Prior to selecting a preset channel in the Preset Search 
mode, you must preset XM Satellite Radio channels. For 
details, see “Setting the XM Satellite Radio preset 
channels” (page 63).
1
Press 
G
SEARCH MODE (or ISRCH 
MODE) repeatedly to select “PRESET 
SEARCH”.
2
Press 
I
CATEGORY (or 9A-E/CAT. l / h
repeatedly to change the preset channel 
group (A to E).
3
Press 
E
PRESET/TUNING/CH l / h (or 
9
PRESET/CH k / n) repeatedly to change 
the preset channel number (1 to 8).
y
You can also select the preset channel number directly by 
pressing the numeric buttons (1 to 8) (B).
■ Direct number access mode
1
Press I
SRCH MODE on the remote control 
repeatedly to select “ALL CH SEARCH” or 
“CAT SEARCH”.
2
Press the numeric buttons (B) to enter the 
desired three-digit channel number.
For example, to enter the number 123, press the 
numeric buttons (B) as shown below.
y
• To display the XM Radio ID number in the front panel display, 
select channel “0”.
• To enter a one-digit or two-digit channel number, press the 
numeric buttons (B) on the remote control and then press 
NENT to confirm the input number.
• Instead of pressing NENT to tune into the channel 
immediately, you can wait a few seconds until this unit confirms 
the entered channel number.
• Pressing a button other than the numeric buttons (B) or NENT 
cancels the Direct Number Access mode procedure.
You can use this feature to store up to 40 XM Satellite 
Radio channels (A1 to E8: 8 preset channel numbers in 
each of the 5 preset channel groups). You can then recall 
any preset channel easily by selecting the preset channel 
group and number as described in “Preset Search mode” 
(page 63).
1
Search for a channel you want to set as a 
preset channel by using one of the XM 
Satellite Radio search modes.
For details, see “XM Satellite Radio operations” 
(page 62).
2
Press 
F
MEMORY (or 0MEMORY).
The PRESET indicator lights up in the front panel 
and this unit automatically selects an empty preset 
number.
y
• To store the selected channel under an empty preset 
number automatically, press and hold 
FMEMORY (or 
0MEMORY) for more than 2 seconds instead of step 2. 
In this case, the following steps are unnecessary.
• To cancel the preset operation, press 
FMEMORY (or 
0MEMORY) again.
3
To select the preset channel group and 
number (A1 to E8), press 
E
PRESET/
TUNING/CH l / h (or 9CAT./A-E l / h 
and 
9
PRESET/CH k / n) repeatedly.
• To select a higher preset channel group and 
number, press 
Eh (or 9k).
• To select a lower preset channel group and number, 
press 
El (or 9n).
y
• You can also select a preset number (1 to 8) by pressing 
the numeric buttons (B).
• If you select a preset number being used (“*” appears next 
to the preset number), the current preset channel will be 
overwritten.
Before performing the following operations, set the operation 
mode selector on the remote control to FSOURCE and then 
press 3XM.
1
2
3
Setting the XM Satellite Radio 
preset channels
0 4 3 X M U
Channel number
PRESET
M E M O R Y A 1
0 4 3 X M U
Lights up