Yamaha RX-V861 User Manual

Use this menu to adjust the optional system parameters.

■ Display settings   A)DISPLAY SET

y

As a result of the parameter setting in “DISPLAY SET”, no 
screen may appear on the video monitor. In such a case, use 
“V.RESET” (see page 96) to set the “VIDEO CONV.”, “HDMI 
UP-SCALING”, “HDMI ASP” and “OSD SHIFT” settings to 
default.

VIDEO CONV.

Use this feature to set whether to convert the video signals 
input at the VIDEO, S VIDEO and COMPONENT 
VIDEO jacks.
Choices: ON, OFF
• Select “ON” to convert video signals (composite, 

S-video or component) to composite, S-video, 
component or HDMI video signals.

• Select “OFF” not to convert any signals.

• This unit does not convert between 480 line video signals and 

576 line video signals.

• The analog component video signals with 480i (NTSC)/576i 

(PAL) of resolution are converted to the S-video or composite 
video signals and output at the S VIDEO MONITOR OUT and 
VIDEO MONITOR OUT jacks.

• The converted video signals are only output at the MONITOR 

OUT jacks. When recording a video source, you must make the 
same type of video connections between each component.

• When composite video or S-video signals from a VCR are 

converted to component video signals, the picture quality may 
suffer depending on your VCR.

• Unconventional signals input at the composite video or S-video 

jacks cannot be converted or may be output abnormally. In such 
cases, set “VIDEO CONV.” to “OFF”.

• When non-standard video signals (such as video signals from a 

game console) are input, this unit may not convert the signals 
even if you set “VIDEO CONV.” to “ON”.

HDMI Up-Scaling

Use this feature to select the resolution of the HDMI up-
conversion of the analog video signals input at the 
VIDEO, S VIDEO and COMPONENT VIDEO jacks so 
that the up-scaled video signals are output at the HDMI 
OUT jack.
This unit up-scales the analog video signals as follows:
• 480i (NTSC)/576i (PAL) 

→ 480p/576p, 1080i or 720p

• 480p/576p 

→ 1080i or 720p

Press Dl / h to select the desired resolution 
and then D

ENTER to confirm the selection.

Choices: THRGH, 480p (or 576p), 1080i, 720p
• Select “THRGH” (through) not to up-scale any analog 

video signals.

• Select “480p” (or “576p”), “1080i” or “720p” to up-

scale analog video signals to 480p or 576p, 1080i or 
720p of resolution.

• The “HDMI UP-SCALING” parameter appears only when you 

set “VIDEO CONV.” to “ON”.

• If you connect your video monitor via HDMI connection, this 

unit automatically detects the available video signal resolution 
of the video monitor, and an asterisk(*) appears on the left of 
the available video signal resolution(s).

• If this unit cannot detect the available video signal resolution(s) 

of the connected video monitor, set “MON. CHK” (see page 93) 
to “SKIP” and then set “HDMI UP-SCALING” again.

• This unit does not convert between 480 line video signals and 

576 line video signals. The resolution availability (“480p” or 
“576p”) depending on the model. However, when the video 
monitor is connected to this unit via HDMI, the available 
resolutions of the monitor appears in the OSD.

MANUAL SETUP

3 OPTION MENU

1/2

p

p

. A)DISPLAY SET

B)MEMORY GUARD
C)AUDIO SELECT
D)PARAM. INI

[ ]/[ ]:Up/Down
[ENTER]:Enter

MANUAL SETUP

3 OPTION MENU

2/2

p

p

. E)ZONE2 SET

F)XM RADIO SET
G)DOCK SET

[ ]/[ ]:Up/Down
[ENTER]:Enter

OPTION MENU

A)DISPLAY SET

1/2

. VIDEO-CONV.;;;ON

HDMI UP-SCALING

>*THRGH

*480p

*1080i

*720p

[ ]/[ ]:Up/Down
[ ]/[ ]:Select

p

p

[

[

OPTION MENU

A)DISPLAY SET

2/2

. DIMMER;;;;;;;;;0

OSD-SHIFT

;;;;;;0

OSD-SOURCE

;;;30s

OSD-AMP

;;;;;;30s

FL SCROLL

;;;CONT

[ ]/[ ]:Up/Down
[ ]/[ ]:Select

p

p

[

[