Yamaha RX-V3300 User Manual
49
English
INTR
ODUCTION
PREP
ARA
TION
B
ASIC OPERA-
TION
AD
V
ANCED
OPERA
TION
ADDITIONAL
INFORMA
TION
APPENDIX
REMOTE CONTROL FEATURES
LEARN
Changing the Source Name in the
Display Window
Display Window
You can change the name that appears in the display
window on the remote control if you want to use the
different name from the original input selector button
names. This is useful when different component is set in
the input selector button.
window on the remote control if you want to use the
different name from the original input selector button
names. This is useful when different component is set in
the input selector button.
1
Press an input selector button, Å or ı to
select the source component you want to
rename.
The selected component name appears in the display
window.
select the source component you want to
rename.
The selected component name appears in the display
window.
2
Press RE-NAME by using
a ballpoint pen or similar
object.
a ballpoint pen or similar
object.
3
Press k / n to select a character.
Choices are A to Z, a to z, 0 to 9, space, -(hyphen),
and /(slash).
Choices are A to Z, a to z, 0 to 9, space, -(hyphen),
and /(slash).
4
Press l / h to move the cursor to the next
position.
position.
y
• If you continuously want to rename another source component,
press ENTER and repeat steps 1, 3 and 4.
5
Press RE-NAME again to exit from the
renaming mode.
renaming mode.
Note
• “ERROR” appears in the display window when pressing
buttons other than indicated in each step, or more than one
button at once.
button at once.
RE-NAME
ENTER
ENTER
PHONO
A
B
CD
DVD
VCR2/DVR
VCR 1
D-TV/LD
CBL/SAT
CD-R
MD/TAPE
TUNER
V-AUX
RE-NAME
TRANSMIT
RE-NAME
ST
ANDBY
6CH INPUT
SYSTEM
CLEAR
LEARN
MACRO
OFF
ON
MACRO
PHONO
A
B
CD
DVD
VCR2/DVR
VCR 1
TITLE
SOURCE
ENTER
D-TV/LD
CBL/SA
T
CD-R
MD/T
APE
TUNER
V
-AUX
POWER
6
Press and hold the button on the other
remote control that has the function you
want to program into this remote control
until “OK” appears in the display window.
remote control that has the function you
want to program into this remote control
until “OK” appears in the display window.
Notes
• “NG” appears in the display window when programming has
not been done correctly. In this case, start over from step 5.
• This remote control can learn approximately 120 functions.
However depending on the signals learned, “FULL” may
appear in the display window much earlier than this number. In
this case, clear unnecessary programmed functions to make
further learning on the remote control.
appear in the display window much earlier than this number. In
this case, clear unnecessary programmed functions to make
further learning on the remote control.
7
Repeat steps 5 and 6 to program additional
functions.
functions.
y
• To learn functions in other source component control area,
press SOURCE SELECT k / n in step 4 to select other source
component.
component.
8
Press LEARN again to exit from the learning
mode.
mode.
Notes
• Learning may not be possible in the following cases:
– when the batteries in the remote control for this unit or other
components are weak
– when the distance between the two remote controls is too
much or too little
– when the remote control infrared windows are not facing at
the appropriate angle
– when the remote control is exposed to the direct sunlight
– when the function to be programmed is continuous or
– when the function to be programmed is continuous or
uncommon
• “ERROR” appears in the display window when pressing
buttons other than indicated in each step, or more than one
button at once.
button at once.
0108V3300_46-59_EN(UA)
02.7.24, 6:06 PM
49