Yamaha HTR-6080 User Guide
55
En
XM Satellite Radio tuning
BA
S
IC
OPERA
T
ION
English
■ All Channel Search mode
1
Press 2
SEARCH MODE (or NSRCH
MODE) repeatedly to select “ALL CH
SEARCH”.
SEARCH”.
2
Press 5
PRESET/TUNING/CH l / h (or
D
PRESET/CH k / n) repeatedly to search
for a channel within all channels.
y
• You can search for a channel quickly by pressing and
holding 5PRESET/TUNING/CH l / h (or
DPRESET/CH k / n).
DPRESET/CH k / n).
• To display the XM Radio ID number displayed in the front
panel display, select channel “0”.
■ Category Search mode
1
Press 2
SEARCH MODE (or NSRCH
MODE) repeatedly to select “CAT SEARCH”.
2
Press 4
CATEGORY (or DA-E/CAT. l / h)
repeatedly to change the channel category.
3
Press 5
PRESET/TUNING/CH l / h (or
D
PRESET/CH k / n) repeatedly to search
for a channel within the selected channel
category.
category.
y
You can search for a channel quickly by pressing and
holding 5PRESET/TUNING/CH l / h on the front
panel (or DPRESET/CH k / n on the remote control).
holding 5PRESET/TUNING/CH l / h on the front
panel (or DPRESET/CH k / n on the remote control).
■ Preset Search mode
Prior to selecting a preset channel in the Preset Search
mode, you must preset XM Satellite Radio channels. For
details, see “Setting the XM Satellite Radio preset
channels” on page 56.
Prior to selecting a preset channel in the Preset Search
mode, you must preset XM Satellite Radio channels. For
details, see “Setting the XM Satellite Radio preset
channels” on page 56.
y
The initial factory setting of all preset channels (A1 to E8) is
“[001] Preview”.
“[001] Preview”.
1
Press 2
SEARCH MODE (or NSRCH
MODE) repeatedly to select “PRESET
SEARCH”.
SEARCH”.
2
Press 4
CATEGORY (or DA-E/CAT. l / h)
repeatedly to change the preset channel
group (A to E).
group (A to E).
3
Press 5
PRESET/TUNING/CH l / h (or
D
PRESET/CH k / n) repeatedly to change
the preset channel number (1 to 8).
y
You can also select the preset channel number directly by
pressing the numeric buttons (1 to 8) (B).
pressing the numeric buttons (1 to 8) (B).
■ Direct number access mode
1
Press N
SRCH MODE on the remote control
repeatedly to select “ALL CH SEARCH” or
“CAT SEARCH”.
“CAT SEARCH”.
2
Press the numeric buttons (B) to enter the
desired three-digit channel number.
For example, to enter the number 123, press the
numeric buttons (B) as shown below.
desired three-digit channel number.
For example, to enter the number 123, press the
numeric buttons (B) as shown below.
The display changes as follows.
y
• To enter a one-digit or two-digit channel number, press the
numeric buttons (B) on the remote control and then press
MENT to confirm the input number.
MENT to confirm the input number.
• Instead of pressing MENT to tune into the channel
immediately, you can wait a few seconds until this unit
confirms the entered channel number.
confirms the entered channel number.
• If no button is pressed within a few seconds after you enter
a one-digit or two-digit number, this unit automatically
confirms the entered channel number.
confirms the entered channel number.
• Pressing a button other than the numeric buttons (B) or
MENT cancels the Direct Number Access mode
procedure.
procedure.
Before performing the following operations, set the operation
mode selector on the remote control to KSOURCE.
mode selector on the remote control to KSOURCE.
1
CLASSICAL
2
LIVE/CLUB
3
ENTERTAIN
<XM> --1
<XM> -12
<XM>123