Manualsbrain.com
  1. Manuals
  2. Brands
  3. Kenwood
  4. KRF-V8300D
  5. User Manual

Kenwood KRF-V8300D User Manual

Download
Page of 72
68
   
KRF-V9300D/KRF-V8300D/KRF-V7300D
Tr
o
u
b
le
sh
o
o
ti
n
g
Symptom
Cause
Remedy
The video is not output or is disturbed.
The video component is not connected properly.
Connect it properly by referring to <Connections>.
 
$ – ª
If the video component is connected to this unit through 
HDMI connection, the digital video signal input from the 
HDMI input terminals is output only at the HDMI monitor 
output terminal.
Video signal may not be output depending on the 
connecting method and connected components.
Refer to the instruction manuals that come with the 
connected components.
The input of the TV monitor is not set properly.
Confirm the input setup of the TV monitor.
A non NTSC/PAL video signal is input.
Set the video setup of the video player component to 
NTSC/PAL. Refer to the instruction manual of the video 
player component.
The HDMI video input is set to "Off" in the HDMI setup.
Perform the HDMI setup again by referring to <HDMI 
input setup –"HDMI Input"–>. 
‚
PURE AUDIO MODE is set to "ON".
If PURE AUDIO MODE is set to "ON", 
the video circuitry is switched off and only the input HDMI 
video can be output. Set PURE AUDIO MODE to "OFF".
 
y
Display is turned off.
PURE AUDIO MODE is on.
While the PURE AUDIO MODE is on, the display is turned 
off. Turn off the PURE AUDIO MODE. 
y
Tuner
Symptom
Cause
Remedy
Radio stations cannot be received.
No antenna is connected.
Connect an antenna. 
•
The broadcast band is not set properly.
Set the broadcast band properly. 
Y
The frequency of the desired station is not tuned.
Tune in the frequency of the desired station. 
Y
Interference
Noise due to ignition of an automobile.
Install the outdoor antenna away from the road.
Noise due to interference from an electric appliance.
Turn off the power to the appliance.
Noise due to a nearby TV set.
Install the unit farther away from the TV.
Remote control unit
Symptom
Cause
Remedy
Remote control operation is not possible.
The remote control is not set to the source operation 
mode you wish to control.
Press the appropriate Input Source key to select the source 
you wish to control.
The remote control has not been changed to the operation 
mode for the Kenwood DVD player you wish to control.
Press the [DVD] key to activate the operation mode for the 
component you want to control before operation. 
Á
Batteries are exhausted.
Replace with new batteries.  
@
The remote control unit is too far away from the main 
system, controlling angle is too large, or there is an 
obstacle between this unit and the remote.
Operate the remote control unit within the controllable 
range. 
#
There is an obstacle between this unit and the remote 
control unit.
Remove the obstacle.
Operation is attempted while recording mode is set to on. Some funcions cannot control while the recording mode 
is set to on. When not recording, set the recording mode 
to off. 
P
Resetting the Microcomputer
Resetting the Microcomputer
If the unit is completely inoperable, the display is not normal or a problem cannot be solved even after checking the list in 
<Troubleshooting>, it is required to reset the microcomputer in the unit.
While holding down [
] key on the unit, unplug the power cord and plug it back in.
•  Please note that resetting the microcomputer will clear the contents of the memory and return the unit to the state it was in when it left the 
factory.
 Troubleshooting
B60-5740-00_00_EN.indd   68
B60-5740-00_00_EN.indd   68
08.7.17   3:30:39 PM
08.7.17   3:30:39 PM