Integra DTR-10.5 User Manual

 

119

 

This menu allows you to configure the listening mode settings including audio effects and playback options.

 

You can switch the volume indication between an 
absolute value and a relative value. 

 

 Displayed in a range from 0 

to 100. 

 

 Displayed in a 

range of –

 

∞

 

 dB, –81.5 dB, –80 dB......18.0 dB. An 

absolute volume value of 82 is equivalent to a relative 
volume value of 0 dB.

 

You can adjust the volume level of muted sounds. 
Specify at 10 dB intervals in a range from –

 

∞

 

 dB and –

50 dB to –10 dB. The default is “–

 

∞

 

.”

This option can be set for Main B and Zone 2 as well as 
for Main A.

 

You can set the maximum output volume level to 
prevent sounds from becoming too loud. When 
displaying in absolute values, specify at 0.5 intervals in 
a range from 50.0 to 99.5. When displaying in relative 
values, specify at 0.5 dB intervals in a range from –32 
dB to +17.5 dB. If you do not want to set any specific 
value, leave this item “Off,” the default setting.
This option can be set for Main B and Zone 2 as well as 
for Main A.

 

You can set a constant volume level of sounds output 
when the DTR-10.5 is powered on. When displaying in 
absolute values, specify at 0.5 intervals in a range from 
0 to 100. When displaying in relative values, specify at 
0.5 dB intervals in a range from –

 

∞

 

 dB and –81.5 dB to 

+18 dB (Max). If you want to maintain a selected 
volume level setting when putting the apparatus into 
standby status, select “Last.” 
This option can be set for Main B and Zone 2 as well as 
for Main A.

 

When the volume level differs between speakers and 
headphones, you can, in advance, fine tune the 
headphones volume. Adjust at 0.5 dB intervals in a 
range from –12 dB to +12 dB.

 

Specify whether or not to display the On Screen Display 
(OSD) on the TV screen connected to the component 

video terminal. This option can be set for both Main A 
and Main B. This item is only available if both of input 
and output devices are connected via the component 
video terminals.

 

 OSD is displayed. 

 

 OSD is not displayed. 

 

Specify whether or not to display the description of 
operations on the screen while you are operating the 
DTR-10.5 (when the component video signal is output, 
nothing is displayed if set to On). This option can be set 
for Main B and Zone 2 as well as for Main A.

 

Displayed. 

 

 Not displayed.

 

Specify the position where the Immediate Display 
should be displayed. You can set in a range of ten 
positions from Top to Bottom of the screen. By default, 
it is displayed at the Bottom of the screen. This option 
can be set for Main B and Zone 2 as well as for Main A. 

 

Specify whether or not to output the video signal with 
interlace mode.

 

 Outputs with interlace mode.

 

 Does not output with interlace mode.

 

This item appears when the ETHERNET terminal board 
[B] (for Net-Audio) is inserted.
Specify whether or not to display a description of 
operations on the screen when using Net-Tune (when 
the component video signal is output, nothing is 
displayed if set to On). This option can be set for Main 
B and Zone 2 as well as for Main A.

 

Displayed. 

 

 Not displayed. 

This sub-menu allows you to adjust the position of the 
OSD Setup Menu as it is displayed on your screen. 
Depending on the monitor used, there may be cases 
where the OSD Setup Menu is not displayed in the 
center and parts of the menus are cut off. To adjust the 
position of the OSD Setup Menu, simply press the 
cursor buttons to inch the menu to the position you 
desire. This option can be set for Main B and Zone 2 as 
well as for Main A.