Philips C70 User Manual
3139 116 19441 (ENG)
7
General Information
• The typeplate (which contains
the serial number) is located at
the rear of the system.
the rear of the system.
• Recording is permissible if
copyright or other rights of third
parties are not infringed.
parties are not infringed.
• This device complies with the
Federal Communications
Commission (FCC) rules, part 15
and with 21 CFR 1040.10.
Operation is subject to the
following two conditions:
– This device may not cause
Commission (FCC) rules, part 15
and with 21 CFR 1040.10.
Operation is subject to the
following two conditions:
– This device may not cause
harmful interference, and
– This device must accept any
interference received, including
interference that may cause
undesired operation.
interference that may cause
undesired operation.
Environmental
Information
Information
All unnecessary packaging has been
omitted. We have tried to make the
packaging easy to separate into three
materials: cardboard (box), polystyrene
foam (buffer) and polyethylene (bags,
protective foam sheet).
omitted. We have tried to make the
packaging easy to separate into three
materials: cardboard (box), polystyrene
foam (buffer) and polyethylene (bags,
protective foam sheet).
Your system consists of materials which
can be recycled and reused if
disassembled by a specialized company.
Please observe the local regulations
regarding the disposal of packaging
materials, exhausted batteries and old
equipment.
can be recycled and reused if
disassembled by a specialized company.
Please observe the local regulations
regarding the disposal of packaging
materials, exhausted batteries and old
equipment.
Accessories
(Supplied)
– Remote control
– Batteries (two AA size) for remote
– Batteries (two AA size) for remote
control
– AM loop antenna
– FM wire antenna
– AC power cord
– SS-115 surround speakers (for model
– FM wire antenna
– AC power cord
– SS-115 surround speakers (for model
FW-C70 only)
– SS-107 surround speakers (for model
FW-C50 only)
GENERAL INFORMATION SAFETY INFORMATION
CLASS 1
LASER PRODUCT
Safety Information
• Before operating the system, check
that the operating voltage indicated
on the typeplate (or the voltage
indication beside the voltage
selector) of your system is identical
with the voltage of your local power
supply. If not, please consult your
dealer. The typeplate is located at the
rear of your system.
on the typeplate (or the voltage
indication beside the voltage
selector) of your system is identical
with the voltage of your local power
supply. If not, please consult your
dealer. The typeplate is located at the
rear of your system.
• When the system is switched on, do
not move it around.
• Place the system on a solid base (e.g.
a cabinet).
• Place the system in a location with
adequate ventilation to prevent
internal heat build-up in your system.
Allow at least 10cm (4 inches)
clearance from the rear and the top
of the unit and 5cm (2 inches) from
the each side.
internal heat build-up in your system.
Allow at least 10cm (4 inches)
clearance from the rear and the top
of the unit and 5cm (2 inches) from
the each side.
• The system incorporates a built-in
safety feature that prevents
overheating.
overheating.
• Do not expose the system to
excessive moisture, rain, sand or heat
sources.
sources.
• Under no circumstances should you
repair the system yourself, as this will
invalidate the warranty!
invalidate the warranty!
• If the system is brought directly from
a cold to a warm location, or is
placed in a very damp room,
moisture may condense on the lens
of the CD unit inside the system.
Should this occur, the CD player will
not operate normally. Leave the
power on for about one hour with
no disc in the system until normal
playback is possible.
placed in a very damp room,
moisture may condense on the lens
of the CD unit inside the system.
Should this occur, the CD player will
not operate normally. Leave the
power on for about one hour with
no disc in the system until normal
playback is possible.
• Electrostatic discharge may cause
unexpected problems. See whether
these problems disappear if you
unplug the AC power cord and plug
it in again after a few seconds.
these problems disappear if you
unplug the AC power cord and plug
it in again after a few seconds.
• To disconnect the system from
the power supply completely,
remove the AC power plug
from the wall socket.
remove the AC power plug
from the wall socket.
pg 01-28/C50-C70/37-Eng
18/11/1999, 2:38 PM
7