Pioneer VSX-1121-K User Manual
En
53
09
Using other functions
Resetting the system
Use this procedure to reset all the receiver’s
settings to the factory default. Use the front
panel controls to do this. Set MULTI-ZONE to
MULTI ZONE OFF.
! Disconnect the iPod and USB memory device
settings to the factory default. Use the front
panel controls to do this. Set MULTI-ZONE to
MULTI ZONE OFF.
! Disconnect the iPod and USB memory device
from the receiver beforehand.
! Set the Control with HDMI to OFF (see HDMI
Setup on page 45 ).
1 Switch the receiver into standby.
2 While holding down ENTER on the
front panel, press u STANDBY/ON.
The display shows RESET c NO d.
3 Select ‘RESET’ using PRESET
2 While holding down ENTER on the
front panel, press u STANDBY/ON.
The display shows RESET c NO d.
3 Select ‘RESET’ using PRESET
k/l,
then press ENTER on the front panel.
The display shows RESET? OK.
4 Press ENTER to confirm.
OK appears in the display to indicate that the
receiver has been reset to the factory default
settings.
The display shows RESET? OK.
4 Press ENTER to confirm.
OK appears in the display to indicate that the
receiver has been reset to the factory default
settings.
! Note that all settings will be saved, even if the
receiver is unplugged.
Default system settings
Setting
Default
Digital Video Converter
ON
SPEAKERS
SB/FH
Speaker System
Normal
(SB/FH)
(SB/FH)
Speaker Setting
Front
SMALL
Center
SMALL
FH/FW
SMALL
Surr
SMALL
SB
SMALLx2
SW
YES
Surround Position
IN REAR
Crossover
80 Hz
X-Curve
OFF
DIMMER
Brightest
Inputs
See Input function default and possible settings on
page 27 .
HDMI
HDMI Audio
See Input function default and possible settings on
page 27 .
HDMI
HDMI Audio
Amp
Control
ON
Control Mode
PQLS
Display Power Off
NO
Audio playback
Power On Level
Power On Level
LAST
Volume Limit
OFF
Mute Level
FULL
Phase Control
ON
Auto Sound
Retriever
Retriever
iPod/USB,
HOME MEDIA
GALLERY,
ADAPTER PORT
input function
HOME MEDIA
GALLERY,
ADAPTER PORT
input function
ON
Other input
functions
functions
OFF
Sound Delay
0.0 frame
Dual Mono
CH1
Setting
Default
DRC
AUTO
SACD Gain
0 dB
LFE Attenuate
0 dB
Auto delay
OFF
Digital Safety
OFF
Effect Level
ExtendedStereo
90
Other modes
50
2
PL II Music
Options
Center Width
3
Dimension
0
Panorama
OFF
Neo:6 Options
Center Image
Neo:6
CINEMA: 10
Neo:6
MUSIC: 3
CINEMA: 10
Neo:6
MUSIC: 3
2
PL IIz Options
Height Gain
MID
All Inputs
Listening Mode
(2 ch/multi ch)
(2 ch/multi ch)
AUTO
SURROUND
SURROUND
Listening Mode
(Headphones)
(Headphones)
STEREO
See also Setting the Audio options on page 48 for
other default DSP settings.
MCACC
other default DSP settings.
MCACC
MCACC Position Memory
M1:
MEMORY 1
MEMORY 1
Channel Level (M1 to M6)
0.0 dB
Speaker Distance (M1 to M6)
10’00’’
Standing Wave
(M1 to M6)
(M1 to M6)
ATT of all
channels/filters
channels/filters
0.0 dB
SWch Wide Trim 0.0 dB
EQ Data (M1
to M6)
to M6)
All channels/
bands
bands
0.0 dB
EQ Wide Trim
0.0 dB