Pioneer VSX-AX3-K User Manual
Techno Tidbits and Problem-solving
96
En
Cause
Remedy
Troubleshooting
Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong
with this component, check the points below. Sometimes the trouble may lie in another component. Investigate the
other components and electrical appliances being used. If the trouble cannot be rectified even after exercising the
checks listed below, ask your nearest PIONEER authorized service center or your dealer to carry out repair work.
with this component, check the points below. Sometimes the trouble may lie in another component. Investigate the
other components and electrical appliances being used. If the trouble cannot be rectified even after exercising the
checks listed below, ask your nearest PIONEER authorized service center or your dealer to carry out repair work.
The power does not turn on
• The power plug is disconnected.
• The protection circuit may have been
activated.
• Connect the power plug to the wall
outlet.
• Disconnect the power plug from the
outlet, and insert again.
During loud playback the
power suddenly switches off.
power suddenly switches off.
• The protection circuit has been activated
because the lowest actual impedance of
the speakers (as opposed to the speak-
ers’ rated impedance) is dangerously
low.
the speakers (as opposed to the speak-
ers’ rated impedance) is dangerously
low.
• Turn down the volume.
• When it’s convenient go to ACOUSTIC
• When it’s convenient go to ACOUSTIC
CAL EQ (see page 87) and lower the 63
Hz and 125 Hz equalizer levels using
manual setting.
Hz and 125 Hz equalizer levels using
manual setting.
• Turning DIGITAL SAFETY on may allow
you to turn up the volume a little more.
(From the Standby mode, and while
holding down the MULTI JOG CON-
TROL SET UP button press the
STANDBY/ON button. Each action
switches SAFETY ON or OFF.)
(From the Standby mode, and while
holding down the MULTI JOG CON-
TROL SET UP button press the
STANDBY/ON button. Each action
switches SAFETY ON or OFF.)
The unit does not respond
when the buttons are pressed.
when the buttons are pressed.
• Static electricity caused by dry air.
• Switch the unit off, then on again.
• Disconnect the power plug from the
• Disconnect the power plug from the
outlet, and insert again.
During operation, the unit
suddenly switches off.
suddenly switches off.
• The speaker wires are frayed or sticking
out of the jack, and are touching the
back of the receiver or another set of
wires.
back of the receiver or another set of
wires.
• Reinsert the speaker wires, making
sure there are no stray strands of wire
and that they are inserted fully (see
page 25).
and that they are inserted fully (see
page 25).
AMP ERR blinks in the display
and the unit turns off. The
STANDBY indicator will blink
and the unit cannot be turned
on.
and the unit turns off. The
STANDBY indicator will blink
and the unit cannot be turned
on.
• The receiver probably has a serious
problem.
• Don’t try to turn on the receiver. Call a
Pioneer-accredited repair center to
look at the problem.
look at the problem.
FAN STOP blinks in the display
and the unit turns off.
and the unit turns off.
• Something is stuck in the fan and/or the
fan is broken.
• Remove the foreign object from the
fan. If you can’t do this and/or the fan
is broken call a Pioneer-accredited
repair center to look at the problem.
is broken call a Pioneer-accredited
repair center to look at the problem.
OVERHEAT blinks in the
display and no sound is
output.
display and no sound is
output.
• The receiver has gotten too hot.
• Turn the receiver off and allow it to cool
down with good ventilation. It is very
likely that you have a heat dispersal
and ventilation problem so please
follow the instructions in “Installing the
Receiver” on page 2 carefully.
likely that you have a heat dispersal
and ventilation problem so please
follow the instructions in “Installing the
Receiver” on page 2 carefully.
THDCT NG blinks in the
display and the unit turns off.
display and the unit turns off.
• The thermistor (temperature sensor) is
broken.
• Turn the receiver off, unplug from wall
and call a Pioneer-accredited repair
center to look at the problem.
center to look at the problem.
Symptom
Power
00_VSX-AX3.book Page 96 Monday, May 19, 2003 1:05 PM