Pioneer VSX-D3S User Manual
<
ARB7050
>
16
OPERATING THE TUNER
Press the POWER switch to the ON position.
Select TUNER with the input selector button.
Be sure to turn the TAPE 2 MONITOR button off when listening to
AM or FM broadcasts.
Switch on the SPEAKERS button corresponding to the speakers
you wish to use.
Select TUNER with the input selector button.
Be sure to turn the TAPE 2 MONITOR button off when listening to
AM or FM broadcasts.
Switch on the SPEAKERS button corresponding to the speakers
you wish to use.
FM auto stereo reception and monaural reception
Each time you press the MPX MODE button, the MONO indicator
in the display section lights or goes out.
÷ If an FM stereo broadcast is received when the MONO indicator
in the display section lights or goes out.
÷ If an FM stereo broadcast is received when the MONO indicator
is out, the STEREO indicator lights and sound is in stereo.
÷ If an FM stereo broadcast is received when the MONO indicator
is lit, the sound will be monaural. If there is interference during
stereo mode reception, switch to mono. The sound will become
monaural but interference will be reduced.
stereo mode reception, switch to mono. The sound will become
monaural but interference will be reduced.
TUNING INTO STATIONS
Turn the MULTI-JOG and the tuning frequency changes.
(Switch off when the GUI MODE button is on.)
Turning in a clockwise direction raises the frequency, while
turning in a counterclockwise direction lowers the frequency.
(Switch off when the GUI MODE button is on.)
Turning in a clockwise direction raises the frequency, while
turning in a counterclockwise direction lowers the frequency.
FREQUENCY PRESETTING
Switch off when the GUI MODE button is on.
1. Tune into the desired station.
See the section “TUNING INTO STATIONS”.
In addition to station frequencies, the MPX MODE (auto
stereo mode or monaural mode) can also be preset (FM
only).
In addition to station frequencies, the MPX MODE (auto
stereo mode or monaural mode) can also be preset (FM
only).
2. Press the MEMORY button.
The station (channel) number flashes in the display. (Memory
mode.)
mode.)
3. Turn the MULTI-JOG to select the station (channel) you
want to memorize.
4. Press the MEMORY button.
÷ The station (channel) number lights in the display, indicating
that it has been memorized.
÷ If you do not press the MEMORY button within about five
seconds after selecting a station, the memory mode is
canceled.
canceled.
5. Repeat steps 1 to 4 to preset additional stations.
A total of 30 AM and FM stations may be preset. When you
store a new preset, it takes the place of the previously stored
station (if any).
store a new preset, it takes the place of the previously stored
station (if any).
You can also preset using GUI. (Refer to page 25.)
LISTENING TO BROADCASTS USING
PRESET TUNING
PRESET TUNING
1. Use the FM/AM button to select either FM or AM.
When the “ST CALL” indicator is lit in the display, press the
SELECT button to switch it off.
SELECT button to switch it off.
2. Turn the MULTI-JOG until you reach the frequency of a
desired station.
When a station is received, the TUNED indicator will light up.
When a station is received, the TUNED indicator will light up.
NOTE:
The TUNED indicator may not light with broadcasts received
over long distances, or when the broadcast signals are extremely
weak.
The TUNED indicator may not light with broadcasts received
over long distances, or when the broadcast signals are extremely
weak.
3. Adjust the volume and tone as desired.
Auto tuning
Auto tuning is convenient when you do not remember the
frequency of a desired station, or when you wish to find stations
that you do not normally listen to.
Operate by remote control. (Refer to page 23.)
frequency of a desired station, or when you wish to find stations
that you do not normally listen to.
Operate by remote control. (Refer to page 23.)
You can also perform Auto Tuning using GUI. (Refer to page 25.)
Switch off when the GUI MODE button is on.
1. Press the SELECT button.
The “ST CALL” indicator lights in the display and the mode
switches to station call.
switches to station call.
2. Turn the MULTI-JOG to select a station.
3. Adjust the volume and tone as desired.
3. Adjust the volume and tone as desired.
When operating by remote control, press the ST +/– buttons to
select a memorized station. (Refer to page 23.)
select a memorized station. (Refer to page 23.)
With GUI, you can also select preset channels. (Refer to page 25.)
1
2
GUI MODE
3
SELECT
1
2
GUI MODE
3
2, 4
GUI MODE
3
MPX MODE