Sony STR-DN1000 User Manual
133
US
A
d
d
it
io
n
a
l In
fo
rm
a
a
tio
n
If there is a malfunction, the display shows a
message. You can check the condition of the
system by the message. See the following table
to solve the problem. If any problem persists,
consult your nearest Sony dealer.
message. You can check the condition of the
system by the message. See the following table
to solve the problem. If any problem persists,
consult your nearest Sony dealer.
PROTECTOR
Irregular current is output to the speakers, or
upper panel of the receiver is covered with
something. The receiver will automatically
turn off after a few seconds. Check the
speaker connection and turn on the power
again.
upper panel of the receiver is covered with
something. The receiver will automatically
turn off after a few seconds. Check the
speaker connection and turn on the power
again.
For other messages, see “Message list after
Auto Calibration measurement” (page 44),
“DIGITAL MEDIA PORT message list”
(page 52) and “SIRIUS Satellite Radio
message list” (page 62).
Auto Calibration measurement” (page 44),
“DIGITAL MEDIA PORT message list”
(page 52) and “SIRIUS Satellite Radio
message list” (page 62).
If you are unable to remedy the problem using
the troubleshooting guide, clearing the
receiver’s memory may remedy the problem
(page 36). However, note that all memorized
settings will be reset to their initial settings and
you will have to readjust all settings on the
receiver.
If the problem persist, consult your nearest
Sony dealer. Note that if service personnel
changes some parts during repair, these parts
may be retained.
In the event of a problem with S-AIR function,
have a Sony dealer check the entire system
together (S-AIR main unit and S-AIR sub
unit).
the troubleshooting guide, clearing the
receiver’s memory may remedy the problem
(page 36). However, note that all memorized
settings will be reset to their initial settings and
you will have to readjust all settings on the
receiver.
If the problem persist, consult your nearest
Sony dealer. Note that if service personnel
changes some parts during repair, these parts
may be retained.
In the event of a problem with S-AIR function,
have a Sony dealer check the entire system
together (S-AIR main unit and S-AIR sub
unit).
Specifications
AUDIO POWER
SPECIFICATIONS
SPECIFICATIONS
POWER OUTPUT AND TOTAL
HARMONIC DISTORTION:
HARMONIC DISTORTION:
(Models of area code U only)
With 8 ohm loads, both channels driven, from
20 – 20,000 Hz; rated 100 watts per channel
minimum RMS power, with no more than
0.09% total harmonic distortion from 250
milliwatts to rated output.
20 – 20,000 Hz; rated 100 watts per channel
minimum RMS power, with no more than
0.09% total harmonic distortion from 250
milliwatts to rated output.
Amplifier section
Models of area code U, CA
1)
Minimum RMS Output Power
(8 ohms, 20 Hz – 20 kHz, THD 0.09%)
(8 ohms, 20 Hz – 20 kHz, THD 0.09%)
100 W + 100 W
Stereo Mode Output Power
(8 ohms, 1 kHz, THD 1%)
(8 ohms, 1 kHz, THD 1%)
110 W + 110 W
Surround Mode Output Power
2)
(8 ohms, 1 kHz, THD 10%)
150 W per channel
1)
Measured under the following conditions:
2)
Reference power output for front, center, surround
and surround back speakers. Depending on the
sound field settings and the source, there may be
no sound output.
and surround back speakers. Depending on the
sound field settings and the source, there may be
no sound output.
Frequency response
Analog
10 Hz – 70 kHz,
+0.5/–2 dB (with sound
field and equalizer
bypassed)
field and equalizer
bypassed)
Error messages
Reference sections for clearing
the receiver’s memory
the receiver’s memory
To clear
See
All memorized settings
Customized sound fields
Area code
Power requirements
U, CA
120 V AC, 60 Hz
continued