JBL SDEC-3000 User Manual
- 16 -
SDEC -X000 DACS Calibration Manual v1.0.doc
7 Speaker Sound Check
Use the circulating noise generator of the Surround Processor
to confirm that all channels have output and that each speaker
is connected to its corresponding channel.
to confirm that all channels have output and that each speaker
is connected to its corresponding channel.
8 Speaker Phase Test
This procedure uses the Surround Processor to route the
phase tester's output to the appropriate channel for test. Using
a "Y" adapter, connect the phase tester's output to both
channels of the TAPE or AUX input or any available analog
input. Select the input making sure that the processor is set to
the analog input you have selected, use the Surround
Processor's volume control to set the test level. Select PARTY
or 5/7 Channel Stereo Mode to route the test signal to all
speakers. It may be necessary to adjust the volume or mute
certain channels to get a clear and accurate test result.
phase tester's output to the appropriate channel for test. Using
a "Y" adapter, connect the phase tester's output to both
channels of the TAPE or AUX input or any available analog
input. Select the input making sure that the processor is set to
the analog input you have selected, use the Surround
Processor's volume control to set the test level. Select PARTY
or 5/7 Channel Stereo Mode to route the test signal to all
speakers. It may be necessary to adjust the volume or mute
certain channels to get a clear and accurate test result.
8.1 Main Speakers
Use the phase tester to confirm the following driver polarities of
the L-C-R and subwoofers
the L-C-R and subwoofers
Synthesis Everest:
L-C-R UHF
(+)
L-C-R Horns
(+)
L-C-R Mid-bass drivers
(+)
Subwoofers
(+)
Synthesis K2 S9800:
L-C-R UHF
(+)
L-C-R Horns
(-)
L-C-R Mid-bass drivers
(+)
Subwoofers
(+)
Synthesis Atlas SK2-1000:
L-C-R UHF
(+)
L-C-R Horns
(-)
L-C-R Mid-bass drivers
(+)
Subwoofers
(+)
Synthesis One Array:
L-C-R UHF
(-)
L-C-R Horns
(+)
L-C-R Mid-bass drivers
(+)
Subwoofers
(+)
Synthesis Two Array:
L-C-R UHF
(-)
L-C-R Horns
(+)
L-C-R Mid-bass drivers
(+)
Subwoofers
(+)
Synthesis Array Three:
L-C-R UHF
(-)
L-C-R Horns
(+)
L-C-R Mid-bass drivers
(+)
Subwoofers
(+)
Synthesis Four:
L-C-R Tweeters
(-)
L-C-R Mid-range
(-)
L-C-R Mid-bass drivers
(+)
Subwoofers
(+)
Synthesis Project Array:
(except Array 880)
L-R UHF
L-R UHF
(+)
L-R Horns
(+)
L-R Mid-bass drivers
(+)
Subwoofers
(+)
Array 880
C UHF
(-)
C HF
(+)
C Mid-bass drivers
(+)
8.2 Surround Speakers
8.2.1
S4Ai configured as Bipole (default)
The S4Ai can be used as a bipole, dipole or a direct radiating
point source speaker. The default as shipped is bipole. Other
bipole speakers would be similar.
point source speaker. The default as shipped is bipole. Other
bipole speakers would be similar.
Figure 15.