Sony SS-K70ED Manual

4-251-798-11(2)

 

2003  Sony Corporation

Printed in China

• Before connection, turn off the amplifier to avoid

damaging the speaker system.

• This speaker system is driven best by an amplifier or

receiver rated as per the wattage indicated in the
specification section.
A low-powered amplifier could result in signal
clipping which could result in tweeter burn-out.
Therefore, it is recommended to use an amplifier or
receiver with sufficient power rating.

Avoid driving the speaker system continuously with a
wattage exceeding the maximum input power of each
speaker.

• Do not attempt to open the enclosure or remove

speaker units. There are no user-serviceable parts
inside.

• Keep recorded tapes, watches, and personal credit

cards using magnetic coding away from the speaker
system.

• Periodically wipe the cabinet with a soft cloth.

Do not use any type of scouring powder, abrasive pad
or solvent.

• Be sure to install the grill net in the correct direction.

Please note that room acoustics can often produce large
difference in the sound for small changes in speaker
placement.
• Set up your speaker system on a hard, flat floor.
• Place the speaker system against a hard wall with its

back about 10 cm (4 inches) away from a wall. The
proportion of bass increases as you move a speaker
close to intersecting room surfaces (wall and wall,
etc.).

• Place the right and left speakers in a similar acoustic

environment.

• It is recommended that the speaker/listener

relationship be an equilateral triangle.

A

B

C

D

E

L
R

L
R

L
R

A

B

Secure the pedestal (

A

) to the speaker with the

supplied screws (

E

) and washers (

D

). (

A

)

Attach the spikes (B) and the jam nuts (C) to
the bottom of the pedestal (

A

).  Fully insert the

front spikes (B) into the pedestal (

A

). (

A

)

Lay the spike pads (F) (hollow side up) on the
installation site and install the pedestal and
speaker. Using the supplied wrench (G),
adjust the back spikes (B) until the speaker is
level. (

B

)

A

B

Speaker system

3-way, magnetically shielded

Loud speaker units

Woofer:  16.5 cm (6 

1

/

2

 inches), cone

type 

×

 2

Mid range:  16.5 cm (6 

1

/

2

 inches), cone

type
Tweeter:  2.5 cm (1 inch), dome type

Enclosure type

Bass reflex

Rated impedance

8 ohms

Maximum input power

200 watts

Characteristic sensitivity level

90 dB (2.83 V/m)

Efficiency frequency range

39 Hz - 70,000 Hz

Cross over frequency

300 Hz, 4,000 Hz

Dimensions (w/h/d)

Approx. 240 

×

 990 

×

 400 mm

(9 

1

/

2

 

×

 39 

×

 15

 3

/

4

 inches)

Mass

Approx. 20.0 kg (44 lb 2 oz)

Supplied accessories

Pedestal (1)
Spike (4)
Spike pad (4)
Jam nut (4)
Washer (2)
Screw (2)
Wrench (1)

Speaker system

3-way, magnetically shielded

Loud speaker units

Woofer:  16.5 cm (6 

1

/

2

 inches), cone

type
Mid range:  16.5 cm (6 

1

/

2

 inches), cone

type
Tweeter:  2.5 cm (1 inch), dome type

Enclosure type

Bass reflex

Rated impedance

8 ohms

Maximum input power

150 watts

Characteristic sensitivity level

89 dB (2.83V/m)

Efficiency frequency range

42 Hz - 70,000 Hz

Cross over frequency

300 Hz, 4,000Hz

Dimensions (w/h/d)

Approx. 240 

×

 900 

×

 400 mm

(9

 1

/

2 

×

 35

 1

/

2

 

×

 15 

3

/

4

 inches)

Mass

Approx. 17.0 kg (37 lb 8 oz)

Supplied accessories

Pedestal (1)
Spike (4)
Spike pad (4)
Jam nut (4)

                                                      Washer (2)
                                                      Screw (2)

Wrench (1)

Design and specifications are subject to change without notice.