Sony MDS-JE470 Manual
Rec
o
rd
ing
to M
D
s
filename[\\WIN-48\NAKAYAMA 3-1\4233926121 3.14\423392612MDSJE770U2\GB05OPE-
U2.fm]
U2.fm]
17
model name1[MDS-JE770] model name 2 [MDS-JE470]
[4-233-926-12(1)]
masterpage:Left
(3 column)
MDS-JE470
While monitoring the sound, turn AMS
(or press LEVEL +/– repeatedly) to raise
the recording level to its highest level
without turning on “OVER” on the peak
level meters.
While monitoring the sound, turn AMS
(or press LEVEL +/– repeatedly) to raise
the recording level to its highest level
without turning on “OVER” on the peak
level meters.
5
Stop playing the program source.
6
To start recording, continue from step 7
of “Recording to an MD” on page 11.
of “Recording to an MD” on page 11.
Tips
•
You can adjust the recording level by pressing
LEVEL +/– on the remote repeatedly during
recording or recording pause.
LEVEL +/– on the remote repeatedly during
recording or recording pause.
•
Peak hold function freezes the peak level meters at
the highest level reached by the input signal.
the highest level reached by the input signal.
1 While the deck is stopped, press MENU/
NO.
2 Turn AMS (or press
./>
repeatedly)
until “Setup?” appears, then press AMS or
YES.
YES.
3 Turn AMS (or press
./>
repeatedly)
until “P.Hold Off” (factory setting) appears,
then press AMS or YES.
then press AMS or YES.
4 Turn AMS (or press
./>
repeatedly)
to select “P.Hold On”, then press AMS or
YES.
YES.
5 Press MENU/NO.
To turn off the Peak Hold Function, select “P.Hold
Off” in step 4 above.
Off” in step 4 above.
Note
The recording level can only be increased up to
+12.0 dB (for analog recording) or +18.0 dB (for
digital recording) (0.0 dB is the factory setting).
Therefore, if the output level of the connected
component is low, it may not be possible to set the
recording level to maximum.
+12.0 dB (for analog recording) or +18.0 dB (for
digital recording) (0.0 dB is the factory setting).
Therefore, if the output level of the connected
component is low, it may not be possible to set the
recording level to maximum.
Checking the remaining
recordable time on the MD
recordable time on the MD
For MDS-JE770:
Press TIME repeatedly.
Press TIME repeatedly.
1)
You cannot check the information when the level
of the input signal is displayed.
of the input signal is displayed.
2)
Total number of tracks and total recorded time in
the group when the Group function is on.
the group when the Group function is on.
3)
Not shown for premasterd discs.
4)
Time shown in the display differs depending on
the setting of REC MODE.
the setting of REC MODE.
For MDS-JE470:
Press DISPLAY on the remote repeatedly.
Press DISPLAY on the remote repeatedly.
For the information in stop mode, see page 22.
For the information during recording, see
page 11.
For the information during recording, see
page 11.
Monitoring the input signal
(Input Monitor)
(Input Monitor)
You can monitor the selected input signal even
when you are not recording it.
when you are not recording it.
1
Press EJECT
A
to eject the MD.
2
Press INPUT repeatedly to select the
jacks (connector) where the signal you
want to monitor is being input.
jacks (connector) where the signal you
want to monitor is being input.
3
Press REC
z
.
When an analog input is selected
The analog signal input from the ANALOG
IN jacks is output to the DIGITAL OUT
connector (MDS-JE770 only) after A/D
conversion, and then to the ANALOG OUT
jacks and PHONES jack (MDS-JE770 only)
after D/A conversion. “AD – DA” appears in
the display during this time.
IN jacks is output to the DIGITAL OUT
connector (MDS-JE770 only) after A/D
conversion, and then to the ANALOG OUT
jacks and PHONES jack (MDS-JE770 only)
after D/A conversion. “AD – DA” appears in
the display during this time.
Avoid turning on these indicators
While the deck
is
is
The following information
appears
appears
Stopped
Total number of tracks and total
recorded time
recorded time
y Total number
of tracks and remaining recordable
time on the MD
time on the MD
Recording
Track number and recorded time of
the current track
the current track
y Track number
and remaining recordable time
on
the MD
continued