Sony HCD-MD373 User Manual
28
“CPLAY MID”
n “CPLAY OUT” n “CPLAY IN”
4-5-1. Operating the Continuous Playback Mode
1. Entering the continuous playback mode
1 Set the disc in the unit. (Whichever recordable discs or discs for playback only are available.)
2 Press the =0/MD/CD/TUNING – button or )+/MD/CD/TUNING + button and display “CPLAY MODE”.
2 Press the =0/MD/CD/TUNING – button or )+/MD/CD/TUNING + button and display “CPLAY MODE”.
3 Press the ENTER/YES “R” button to change the display to “CPLAY MID”.
4 When access completes, the display changes to “C1 =
4 When access completes, the display changes to “C1 =
AD =
”.
Note : The numbers “ ” displayed show you error rates and ADER.
2. Changing the parts to be played back
1 Press the ENTER/YES “R” button during continuous playback to change the display as below.
When pressed another time, the parts to be played back can be moved.
2 When access completes, the display changes to “C1 =
AD =
”.
Note : The numbers “ ” displayed show you error rates and ADER.
3. Ending the continuous playback mode
1 Press the MENU/NO “R” button. The display will change to “CPLAY MODE”.
2 Press the 6 (MD) button to remove the disc.
Note : The playback start addresses for IN, MID, and OUT are as follows.
2 Press the 6 (MD) button to remove the disc.
Note : The playback start addresses for IN, MID, and OUT are as follows.
IN
40h cluster
MID 300h cluster
OUT 700h cluster
OUT 700h cluster
4-5-2. Operating the Continuous Recording Mode (Use only when performing self-recording/palyback check.)
1. Entering the continuous recording mode
1 Set a recordable disc in the unit.
2 ress the =0/MD/CD/TUNING – button or )+/MD/CD/TUNING + button and display “CREC MODE”.
2 ress the =0/MD/CD/TUNING – button or )+/MD/CD/TUNING + button and display “CREC MODE”.
3 Press the ENTER/YES “R” button to change the display to “CREC MID”.
4 When access completes, the display changes to “CREC (
4 When access completes, the display changes to “CREC (
)” and
r REC indicator lights up.
Note : The numbers “ ” displayed shows you the recording position addresses.
2. Changing the parts to be recorded
1 When the ENTER/YES “R” button is pressed during continuous recording, the display changes as below.
When pressed another time, the parts to be recorded can be changed.
r REC indicator goes off.
2 When access completes, the display changes to “CREC (
)” and
r REC indicator lights up.
Note : The numbers “ ” displayed shows you the recording position addresses.
3. Ending the continuous recording mode
1 Press the MENU/NO “R” button. The display changes to “CREC MODE” and r REC indicator goes off.
2 Press the 6 (MD) button to remove the disc.
Note 1 : The recording start addresses for IN, MID, and OUT are as follows.
Note 1 : The recording start addresses for IN, MID, and OUT are as follows.
IN
40h cluster
MID
300h cluster
OUT
700h cluster
Note 2 : The MENU/NO “R” button can be used to stop recording anytime.
Note 3 : Do not perform continuous recording for long periods of time above 5 minutes.
Note 4 : During continuous recording, be careful not to apply vibration.
Note 3 : Do not perform continuous recording for long periods of time above 5 minutes.
Note 4 : During continuous recording, be careful not to apply vibration.
4-5-3. Non-Volatile Memory Mode (EEP MODE)
This mode reads and writes the contents of the non-volatile memory.
It is not used in servicing. If set accidentally, press the MENU/NO “R” button immediately to exit it.
It is not used in servicing. If set accidentally, press the MENU/NO “R” button immediately to exit it.
“C REC MID”
n “C REC OUT” n “C REC IN”