Sony BDV-IT1000 User Manual
O
the
r O
r O
p
erati
ons
111
GB
Note
• When you perform [Auto Calibration] in the Easy
Setup (page 69), the default settings are changed.
• Depending on the input stream, [Distance] may not
be effective.
x [Level]
You can adjust the sound level of the speakers,
center speaker, and subwoofer. You can set the
parameters from –6.0 dB to +6.0 dB. Be sure to
set [Test Tone] to [On] for easy adjustment.
You can adjust the sound level of the speakers,
center speaker, and subwoofer. You can set the
parameters from –6.0 dB to +6.0 dB. Be sure to
set [Test Tone] to [On] for easy adjustment.
[Front L/R] 0.0 dB: Set the front speaker level.
[Center] 0.0 dB
[Center] 0.0 dB
*
: Set the center speaker level.
[Surround L/R] 0.0 dB
*
: Set the surround
speaker level.
[Surround Back L/R] 0.0 dB
[Surround Back L/R] 0.0 dB
*
: Set the surround
Back speaker level.
[Subwoofer] 0.0 dB: Set the subwoofer level.
[Subwoofer] 0.0 dB: Set the subwoofer level.
* This item appears when you set to [Yes] in the
[Connection] setting.
x [Test Tone]
The speakers will emit a test tone to adjust
[Level].
The speakers will emit a test tone to adjust
[Level].
[Off]: The test tone is not emitted from the
speakers.
[On]: The test tone is emitted from each speaker
in sequence while adjusting level. When you
select one of the [Speaker Settings] items, the
test tone is emitted from each speaker in
sequence.
Adjust the sound level as follows.
speakers.
[On]: The test tone is emitted from each speaker
in sequence while adjusting level. When you
select one of the [Speaker Settings] items, the
test tone is emitted from each speaker in
sequence.
Adjust the sound level as follows.
1
Set the [Test Tone] to [On].
2
Press
C/X/x/c repeatedly to select the
desired speaker and the level.
3
Press .
4
Repeat Steps 1 to 3.
5
Press
C/X/x/c repeatedly to set [Test
Tone] to [Off] after adjusting the
speaker level.
speaker level.
Note
• The test tone signals are not output from the HDMI
OUT jack.
Tip
• To adjust the volume of all the speakers at one time,
press 2 +/–.
Controlling the TV or
Other Components with
the Supplied Remote
Other Components with
the Supplied Remote
By adjusting the remote signal, you can control
your TV, a Sony component (such as a VCR,
DVD player/recorder, etc.), CATV, or set-top
box/digital satellite receiver with the supplied
remote.
your TV, a Sony component (such as a VCR,
DVD player/recorder, etc.), CATV, or set-top
box/digital satellite receiver with the supplied
remote.
Note
• When you replace the batteries of the remote, the
code number may reset itself to the default (SONY)
setting. Reset the appropriate code number.
setting. Reset the appropriate code number.
1
Press POP UP/MENU while pressing
TV (for TV) or STB (for a Sony
component, CATV, set-top box/digital
satellite receiver, etc.).
TV (for TV) or STB (for a Sony
component, CATV, set-top box/digital
satellite receiver, etc.).
TV or STB (pressed button) flashes.
2
While TV or STB is flashing, enter the
manufacturer’s code (see the table)
using the number buttons, then press
TIME.
manufacturer’s code (see the table)
using the number buttons, then press
TIME.
If you successfully set the manufacturer’s
code, TV or STB will flash twice slowly. If
the setting is unsuccessful, TV or STB will
flash five times quickly.
code, TV or STB will flash twice slowly. If
the setting is unsuccessful, TV or STB will
flash five times quickly.
Code numbers of controllable
components
components
If more than one code number is listed, try
entering them one at a time until you find the
code that works with your TV.
entering them one at a time until you find the
code that works with your TV.
TV
Preparing the remote for
controlling the components
controlling the components
Manufacturer
Code number
SONY
5001 (default), 5002
AIWA
5001
AKAI
5003
DAEWOO
5003, 5015, 5044
GE
5003, 5009, 5010, 5044
GOLDSTAR/LG
5003, 5015, 5017, 5044, 5068