Kenwood HM-537MP User Manual
9
EN
Using the CD/MP3-CD
Loading a disc
1 Press CD button to select CD/MP3 mode.
2 Press 0 open/close button to open the CD
tray.
3 Place a CD/MP3 into the tray with the label
facing up.
4 Press 0 open/close button to close the CD
tray.
The total playtime and total number of tracks
will appear in the display.
will appear in the display.
5 To remove the CD, press 0 open/close but-
ton, grasp the CD by its edges, and carefully
pull it out.
pull it out.
For MP3-CD only
Load a MP3 format music disc on the disc tray.
•
The total album number and total track number
will appear on the display.
will appear on the display.
Notes:
•
To ensure good system performance; wait until the
unit completely reads the disc before proceeding.
unit completely reads the disc before proceeding.
•
If the CD tray is not loaded with a CD/MP3-CD or
the CD/MP3-CD is unreadable, the message “NO
DISC” will be shown.
the CD/MP3-CD is unreadable, the message “NO
DISC” will be shown.
•
For MP3-CD, the disc reading time may exceed 10
seconds due to the large number of songs com-
piled into one disc.
seconds due to the large number of songs com-
piled into one disc.
•
For MP3-CD, “A” on the display represents ALBUM.
•
For MP3-CD, the total album number on the display
indicates the number of all the albums recorded in
the MP3-CD.
indicates the number of all the albums recorded in
the MP3-CD.
Playing a normal disc
1 Press 6 button to start playback.
The track number and elapsed playing time of
the current track appear on the display.
To interrupt playback, press
the current track appear on the display.
To interrupt playback, press
6 button.
The playing time will start flashing.
To resume playback press
To resume playback press
6 button again.
2 To stop playback, press 7 stop button.
Selecting a desired track/passage
To select a desired track
Press
4 or ¢ button (4 or ¢ SEARCH/
TUNING button on the remote control) repeat-
edly until the desired track appears on the display.
edly until the desired track appears on the display.
•
If playback is stopped, press
6 button to start
playback.
•
The digit buttons (0~9) on the remote control
can also be used to select a track.
can also be used to select a track.
Press the digit buttons as shown below:
To select track 2 : 2 and ENTER
To select track 23 : 2, 3 and ENTER
To select track 120 (MP3-CD only) : 1, 2 and 0
To select track 2 : 2 and ENTER
To select track 23 : 2, 3 and ENTER
To select track 120 (MP3-CD only) : 1, 2 and 0
To search for a particular passage during
playback
playback
Press and hold
4 or ¢ button (4 or ¢
SEARCH/TUNING button on the remote control)
and released it when the desired passage is lo-
cated for CD.
and released it when the desired passage is lo-
cated for CD.
Selecting a desired album/file
(For
MP3-CD only)
To select a desired album
To select a desired album
Press p.call/album up or down button on the
unit until the desired album number appears on
the display.
unit until the desired album number appears on
the display.
•
“Axxx xxx” will appear on the display.
To select a desired file
Press
4 or ¢ button (4 or ¢ SEARCH/
TUNING button on the remote control) repeat-
edly until the desired file from the current album
appears on the display.
edly until the desired file from the current album
appears on the display.
•
“Axxx xxx” will appear on the display.
•
The digit buttons (0~9) on the remote control
can also be used to select a file.
can also be used to select a file.
continued to next page
*5469/08-20/EN
04.6.1, 11:20 AM
9