JVC SP-NXF30W User Manual
62
Refer
ence
• The system supports DivX 5.x, 4.x and 3.11.
• The system supports DivX files with a resolution
• The system supports DivX files with a resolution
of 720 x 480 pixels or less (30 fps) and 720 x
576 pixels or less (25 fps).
576 pixels or less (25 fps).
• Audio streams should conform to MPEG1 Audio
Layer-2, MPEG Audio Layer-3 (MP3) or Dolby
Digital.
Digital.
• The system does not support GMC (Global
Motion Compression).
• Files encoded in the interlaced scanning mode
may not be played back correctly.
• Playing back a DivX file may take a long time.
The elapsed time is not displayed until playback
starts. The elapsed time may also not be
displayed correctly.
starts. The elapsed time may also not be
displayed correctly.
• The stream structure of MPEG1/MPEG2 discs
and files should conform to MPEG system/
program stream.
program stream.
• 720 x 576 pixels (25 fps)/720 x 480 pixels (30
fps) is recommended for the highest resolution.
• This system also supports the resolutions of 352
x 576/480 x 576/352 x 288 pixels (25 fps) and
352 x 480/480 x 480/352 x 240 pixels (30 fps).
352 x 480/480 x 480/352 x 240 pixels (30 fps).
• The profile and level should be MP@ML (Main
Profile at Main Level)/SP@ML (Simple Profile at
Main Level)/MP@LL (Main Profile at Low Level).
Main Level)/MP@LL (Main Profile at Low Level).
• Audio streams should conform to MPEG1 Audio
Layer-2, MPEG2 Audio Layer-2 or Dolby Digital
(MPEG2 files only).
(MPEG2 files only).
The Non-DVD side of a “DualDisc” does not
comply with the “Compact Disc Digital Audio”
standard. Therefore, the use of Non-DVD side of a
DualDisc on this product may not be
recommended.
comply with the “Compact Disc Digital Audio”
standard. Therefore, the use of Non-DVD side of a
DualDisc on this product may not be
recommended.
• This system is compatible with USB 2.0 Full-
Speed.
• This system may not play back some USB
devices and some files.
• This system does not support DRM (Digital
Rights Management).
• This system cannot recognize a USB device
whose rating exceeds 5 V/500 mA.
• When connecting a USB device, refer also to its
manual.
• Connect the USB device directly to the main unit
without routing through a USB hub.
• Disconnect the USB device after stopping
playback or turning off this system.
• The main unit can charge a USB device when
the USB device is selected as the source.
• Always set the volume to the minimum on this
system when connecting or disconnecting a
USB device.
USB device.
• JVC bears no responsibility for any loss of data
on the USB device while using this system.
Notes on DivX discs/files
Notes on MPEG1/MPEG2 discs/
files
files
Caution for DualDisc playback
Notes on files recorded on a
connected USB device
connected USB device
How to attach the core filter
Attach the provided core filter to the power cable, then core filter reduces interference.
Attach the provided core filter to the power cable, then core filter reduces interference.
1 Release the stopper of the core filter.
2 Run the cable through the core filter, and wind the cable firmly once inside the cutout of the core filter
2 Run the cable through the core filter, and wind the cable firmly once inside the cutout of the core filter
as shown in the illustration.
3 Close the core filter until it clicks shut.
NOTE
• Do not damage the cable by applying excessive power when winding.
• Do not damage the cable by applying excessive power when winding.
Power
cable
Core filter
Stopper
NX-F30[U].book Page 62 Tuesday, April 21, 2009 6:23 PM