JVC 0209RYMMDWDAT User Manual

CAUTION: Proper Ventilation
To avoid risk of electric shock and fire, and to prevent 
damage, locate the apparatus as follows:
1.  Front: No obstructions and open spacing.
2.  Sides/Top/Back: No obstructions should be placed in the 

areas shown by the dimensions below.

3.  Bottom: Place on the level surface. Maintain an adequate 

air path for ventilation by placing on a stand with a height 
of 10 cm or more.

ATTENTION: Aération correcte
Pour prévenir tout risque de décharge électrique ou 
d’incendie et éviter toute détérioration, installez l’appareil de 
la manière suivante:
1.  Avant: Bien dégagé de tout objet.
2.  Côtés/dessus/dessous: Assurez-vous que rien ne bloque 

les espaces indiqués sur le schéma ci-dessous.

3.  Dessous: Posez l’appareil sur une surface plane et 

horizontale. Veillez à ce que sa ventilation correcte puisse 
se faire en le plaçant sur un support d’au moins dix 
centimètres de hauteur.

Using Headphones
Be sure to turn down the volume before connecting or putting on 
the headphones.
•  Connecting the headphones will deactivate the speakers.
•  Sound adjustments also affect the sound through the headphones.

Display Demonstration
When you plug in the System, the display demonstration 
automatically starts.
To cancel the display demonstration, press and hold DEMO until 
“DEMO CLR” is displayed while the System is on standby.
•  When the ECO Mode is activated, the display demonstration does 

not work (and you cannot deactivate it).

•  When the display demonstration is activated, it also starts if no 

operation is done for about 2 minutes while the System is turned 
on.

Laser Touch Operation
You can use 

4/¢ and VOL +/– on the front panel by sliding 

your finger up or down on the illumination.

Motion Sensor on the Front Panel
When you move your hand close to the front panel while the System 
is on standby, the controls on the front panel illuminate.
•  When no operation is done for about 5 seconds, the illumination 

turns off.

•  When the ECO Mode is activated, the motion sensor does not work.

LVT1989-001A[J/C]

0209RYMMDWDAT

©2009 Victor Company of Japan, Limited

After unpacking, check to be sure that you have all the 
following items.
•  Remote control, RM-SUXGN6J (× 1)
•  Lithium coin battery (× 1: installed in the remote control)
•  AM loop antenna (× 1)
•  FM antenna (× 1)
•  Video cord (× 1)
If anything is missing, consult your dealer immediately.

When you use the remote control for the first time, pull out 
the insulation sheet.

NOTES:
•  Store the battery in a place where children cannot reach. If 

•  To prevent the battery from overheating, cracking, or starting 

  – Do not recharge, short, disassemble or heat the battery or 

  – Do not leave the battery with other metallic materials.
  – Wrap the battery with tape and insulate when throwing 

  – Do not poke the battery with tweezers or similar tools.
•  Dispose of battery in the proper manner, according to federal, 

Play back the disc

•  During playback, press again to pause.

Play back the USB 
mass storage class 
device

Stop playback

•  While playback is stopped, total track number 

and total playing time (for MP3/WMA files, 
group number and track number) appear.

Select a track

Select the next tracks.

To go back to the beginning of the current or 
previous tracks.

Select a group 
(MP3/WMA only)

Select the next groups.

Select the previous groups.

Forward search/
Reverse search

Press and hold to fast-forward the track during 
playback.

Press and hold to fast-reverse the track during 
playback.

Change 
the display 
information

(only for USB)
Press repeatedly.

NOTES:
•  If no disc is inserted or no USB mass storage class device is connected, “NO DISC” or 

•  If MP3/WMA files are not recorded on the disc or in the USB mass storage class device, 

Press repeatedly to specify the repeat mode as follows:

RPT TRK:

Repeats the current (or specified) track. [  1]

RPT GRP:

Repeats all tracks in the current group (MP3/WMA 
only). [   ]

RPT ALL:

Repeats all tracks. [  ALL ]

RPT OFF:

Normal playback

or

This System can play back...
– CD.
– CD-R/CD-RW recorded in audio CD format (CD-DA) or recorded MP3/WMA files 

in ISO 9660 format.

– USB mass storage class device containing MP3/WMA files.
•  When playing back an MP3 or WMA track, corresponding indicator lights up.

(on the System only)

Touch to open the disc tray.

•  When using an 8 cm (3 3/16 inch) disc, place it on 

the inner circle of the disc tray.

Touch to close the disc tray.

You can connect a USB mass storage class device such as a USB flash memory 
device, MP3 player, multimedia card reader, etc. to the System.

NOTES:
•  When connecting with a USB cable, use the USB 2.0 cable whose length is less than 

•  USB mass storage class device is charged through the USB terminal when the System 

•  You cannot connect a computer to the USB terminal of the System.
•  Do not disconnect the USB mass storage class device when the System is turned on. It 

•  Noise and static electricity may stop the USB mass storage class device sound. In this 

•  Depending on the shape of USB mass storage class device, the USB terminal may 

(on the System only)

You can lock the disc tray so that no one can eject the loaded disc.
While the System is on standby...

To cancel the prohibition, repeat the same 
procedure. 

(only for Disc)

Select disc as the source.

Activate the Program Play.

or

Select tracks you want for Program Play.
•  For MP3/WMA files only: You can also use UP or 

DOWN.

Press to store the selected track.

Repeat steps 3 and 4 to program other tracks you want.
•  If you try to program a 33rd track, “PGM FULL” appears.

The tracks are played back in the programmed 
order.

•  To check the programmed contents, press 

4 or ¢.

•  To add tracks, repeat steps 3 and 4 above.
•  To erase the entire program, press and hold CANCEL for about 2 seconds.
•  To exit from Program Play, press PROGRAM or 

7.

  – The stored program is kept.

(only for Disc)

Select disc as the source.

Press repeatedly to select the desired Random Mode.

RANDOM:

Plays all tracks in random order.  [ALL  RND ]

RND GRP:

Plays tracks in the current group in random 
order. (MP3/WMA only). [  RND ]

RND OFF:

Normal playback

Playback starts in random order.

•  To skip a track, press 

¢.

•  To go back to the beginning of the current track, press 

4.

Thank you for purchasing a JVC product.

Turn on or off 
(standby) the power

The STANDBY lamp on the System turns off/on.

Select a source

See “Playing Back a Disc/USB Mass Storage Class Device” 
on page 4.

See “Listening to an iPod/Viewing Images on the iPod” 
on page 5.

Press repeatedly to select “FM,” “AM,” or “AUDIO IN” as 
the source.

•  See “Listening to FM and AM Broadcasts” or “Listening 

to Other Equipment” on page 5.

Adjust the volume

—

Drop the volume in 
a moment

—

To restore the volume, press again, or adjust the 
volume level. 

Select the Sound 
Mode

—

Press repeatedly to select the desired Sound Mode.
The SOUND indicator lights up.

Emphasize the 
sound (Sound 
Turbo)

The S.TURBO indicator lights up.
To cancel this function, press again.

Reinforce the bass 
sound (Hyper Bass 
Sound)

—

The HBS indicator lights up.
•  When Sound Turbo function is activated (see above), 

the HBS indicator goes off and HBS button does not 
work.

To cancel this function, press again.

Change the display 
brightness

Press repeatedly when the System is turned on.

Turn off the display 
while on standby 

Press repeatedly while the System is on standby.

Clock

DISP OFF:

ECO ON:

Turns off the display with the motion sensor 
on.
Turns on the ECO (Ecology) Mode. 
ECO Mode reduces power consumption 
while the System is on standby by turning 
off the display and motion sensor.

NOTE:
DO NOT turn off (standby) the System with the volume set to an extremely high level; otherwise, the sudden 
blast of sound can damage your hearing, speakers and/or headphones when you turn on the System or start 
playback.

Outdoor FM antenna 
(not supplied)

FM antenna (supplied)

NOTES:
•  Make sure the antenna conductors do not touch any other 

•  Keep the AM loop antenna cable wrapped around the AM loop 

•  Make sure both the speakers are connected correctly and firmly.
•  When connecting the speaker cords, match the polarity of the 

•  DO NOT connect more than one speaker to each terminal.
•  DO NOT allow the conductor of the speaker cords to be in touch 

To connect the FM antenna (supplied)
Extend it so that you can obtain the best reception.

Disconnect the supplied FM antenna, and connect 
to an outdoor FM antenna using a 75 Ω wire with 
coaxial type connector.

Press and hold

Insert

Release

Red

Black

From left 
speaker

From right 
speaker

LVT1989-001A   EN_UX-GN6[JC]

USB cable (not 
supplied)

or

USB memory 
(not supplied)

STANDBY lamp

Stereo mini plug cord

PHONES jack

Touch to turn on the System.

To use 

4/¢

To use VOL +/–

To a wall outlet
Plug the AC power cord only after all 
connections are complete.

CA-UXGN6

CA-UXGN6

Turn the AM loop antenna until 
the best reception is obtained.

Red

Black

For customer use:
Enter below the Model No. and Serial No. which are 
located either on the rear, bottom or side of the cabinet. 
Retain this information for future reference.
Model No.
Serial No.

         

 

The lightning flash with arrowhead symbol, 
within an equilateral triangle is intended to 
alert the user to the presence of uninsulated 
“dangerous voltage” within the products 
enclosure that may be of sufficient magnitude 
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral 
triangle is intended to alert the user to 
the presence of important operating and 
maintenance (servicing) instructions in the 
literature accompanying the appliance.

For U.S.A.
This equipment has been tested and found to comply 
with the limits for a Class B digital device, pursuant to part 
15 of the FCC Rules.
These limits are designed to provide reasonable 
protection against harmful interference in a residential 
installation. This equipment generates, uses and can 
radiate radio frequency energy and, if not installed and 
used in accordance with the instructions, may cause 
harmful interference to radio communications. However, 
there is no guarantee that interference will not occur 
in a particular installation. If this equipment does cause 
harmful interference to radio or television reception, which 
can be determined by turning the equipment off and on, 
the user is encouraged to try to correct the interference by 
one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and 
receiver. Connect the equipment into an outlet on a circuit 
different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician 
for help.

Le symbole de l’éclair à l’intérieur d’un triangle 
équilatéral est destiné à alerter l’utilisateur sur 
la présence d’une “tension dangereuse” non 
isolée dans le boîtier du produit. Cette tension 
est suffisante pour provoquer l’électrocution 
de personnes.
Le point d’exclamation à l’intérieur d’un 
triangle équilatéral est destiné à alerter 
l’utilisateur sur la présence d’opérations 
d’entretien importantes au sujet desquelles 
des renseignements se trouvent dans le 
manuel d’instructions.

IMPORTANT FOR LASER PRODUCTS
1.  CLASS 1 LASER PRODUCT
2.  CAUTION: Do not open the top cover or cabinet. There 

are no user serviceable parts inside the unit; leave all 
servicing to qualified service personnel.

3. CAUTION: Visible and/or invisible class 1M laser radiation 

when open. Do not view directly with optical instruments.

4.  REPRODUCTION OF LABEL: CAUTION LABEL, PLACED 

INSIDE THE UNIT.

IMPORTANT POUR PRODUITS LASER
1.  PRODUIT LASER CLASSE 1
2.  ATTENTION: N’ouvrez pas le couvercle supérieur ni 

le coffret de l’appareil. Il n’y a aucune pièce réparable 
par l’utilisateur à l’intérieur de l’appareil; confiez toute 
réparation à un personnel qualifié.

3.  ATTENTION: Rayonnement laser visible et/ou invisible 

de classe 1M une fois ouvert. Ne pas regarder directement 
dans le faisceau avec des instruments optiques.

4.  REPRODUCTION DE L’ÉTIQUETTE: ÉTIQUETTE DE 

PRÉCAUTION PLACÉE À L’INTERIEUR DE L’APPAREIL.

CAUTION:
Changes or modifications not approved by JVC could void 
the user’s authority to operate the equipment.

CAUTION
The 

 button in any position does not disconnect the mains 

line.
Disconnect the mains plug to shut the power off completely 
(the STANDBY lamp goes off).
The MAINS plug or an appliance coupler is used as the 
disconnect device, the disconnect device shall remain readily 
operable.
•  When the System is on standby, the STANDBY lamp lights 

red.

•  When the System is turned on, the STANDBY lamp goes off.
The power can be remote controlled.

ATTENTION
La touche 

, quelle que soit sa position, ne coupe pas la 

ligne principale.
Débrancher la fiche principale pour couper complètement 
l’alimentation du secteur (le témoin STANDBY s’éteint).
La fiche secteur ou un coupleur est utilisé comme dispositif 
de déconnexion de l’appareil, et l’appareil déconnecté doit 
être prêt à être utilisé.
•  Quand l’appareil est en mode d’attente, le témoin STANDBY 

est allumé en rouge.

•  Quand l’appareil est sous tension, le témoin STANDBY s’éteint.
L’alimentation peut être commandée à distance.

CAUTION
To reduce the risk of electrical shocks, fire, etc.:
1.  Do not remove screws, covers or cabinet.
2.  Do not expose this appliance to rain or moisture.

ATTENTION
Afin d’éviter tout risque d’électrocution, d’incendie, etc.:
1.  Ne pas enlever les vis ni les panneaux et ne pas ouvrir le 

coffret de l’appareil.

2.  Ne pas exposer l’appareil à la pluie ni à l’humidité.

CAUTION:
•  Do not block the ventilation openings or holes. (If the 

ventilation openings or holes are blocked by a newspaper 
or cloth, etc., the heat may not be able to get out.)

•  Do not place any naked flame sources, such as lighted 

candles, on the apparatus.

•  When discarding batteries, environmental problems 

must be considered and local rules or laws governing the 
disposal of these batteries must be followed strictly.

•  Do not expose this apparatus to rain, moisture, dripping 

or splashing and that no objects filled with liquids, such as 
vases, shall be placed on the apparatus.

For USA-California Only
This product contains a CR Coin Cell Lithium Battery which 
contains Perchlorate Material – special handling may 
apply.
See www.dtsc.ca.gov/hazardouswaste/perchlorate

Remote sensor

CAUTION: Excessive sound pressure from earphones or 
headphones can cause hearing loss.

ATTENTION: Une pression acoustique excessive des écouteurs 
ou du casque d’écoute peut entraîner une perte auditive.

Lithium coin battery 
(product number: CR2025)

Insulation sheet

To connect the monitor 
(not supplied)
—To view video/picture 
from the iPod

SP-UXGN5

CAUTION: Battery shall not be exposed to excessive heat 
such as sunshine, fire, or the like.

ATTENTION: Les piles ne doivent en aucun cas être 
exposées à une chaleur excessive (lumière du solei, feu, 
etc.).

SP-UXGN5

Point at the remote sensor on the front panel.

Headphones
(not supplied)

CAUTION:
Danger of explosion if battery is incorrectly replaced. 
Replace only with the same or equivalent type.

Monitor

Video cord 
(supplied)

The operations on pages 4 to 6 are explained using the remote control, unless mentioned otherwise. However, if the System has the same or similar button names, they can also be 
used for the operations.

(canceled)

AM loop antenna 
(supplied)

(canceled)

ATTENTION:
•  Ne bloquez pas les orifices ou les trous de ventilation. (Si 

les orifices ou les trous de ventilation sont bloqués par un 
journal un tissu, etc., la chaleur peut ne pas être évacuée 
correctement de l’appareil.)

•  Ne placez aucune source de flamme nue, telle qu’une 

bougie, sur l’appareil.

•  Lors de la mise au rebut des piles, veuillez prendre en 

considération les problèmes de l’environnement et suivre 
strictement les règles et les lois locales sur la mise au rebut 
des piles.

•  N’exposez pas cet appareil à la pluie, à l’humidité, à un 

égouttement ou à des éclaboussures et ne placez pas des 
objets remplis de liquide, tels qu’un vase, sur l’appareil.