Panasonic SC-HC35 User Manual
15
RQ
T
X
12
60
ENGLISH
1
Press [ , iPod] repeatedly to select
“BLUETOOTH”.
“BLUETOOTH”.
2
Press [ MENU] to display “DISCONNECT?”
and then press [OK].
and then press [OK].
A confirmation message is displayed.
3
Press [2, 1] to select “YES” and then press
[OK].
≥ The connection can also be stopped when you disable Bluetooth
®
transmission on the connected Bluetooth
®
device.
Preparation
Press [ , iPod] repeatedly to select “BLUETOOTH”.
Press [ , iPod] repeatedly to select “BLUETOOTH”.
≥ These functions are unavailable if a device is connected. Disconnect the
Bluetooth
®
devices to display these functions.
∫ To register more devices
1
Press [ MENU] repeatedly to select
“NEW DEV.” and then press [OK].
“NEW DEV.” and then press [OK].
≥ The unit enters pairing mode and “PAIRING” starts blinking
on the display.
2
While this unit is in pairing mode, access the
Bluetooth
Bluetooth
®
menu of the Bluetooth
®
device and
execute a Bluetooth
®
search to find this unit
(SC-HC55).
≥ If prompted for the passkey, enter “0000”.
∫ To select communication quality
1
Press [ MENU] repeatedly to select
“LINK MODE”.
“LINK MODE”.
2
Press [2, 1] to select the following modes and
then press [OK].
∫ To select Auto Link mode
1
Press [ MENU] repeatedly to select
“AUTO LINK”.
“AUTO LINK”.
2
Press [2, 1] to select the following modes and
then press [OK].
≥ When “LINKING” is displayed, pressing [
MENU] is invalid.
≥ Auto Link works only if your device supports A2DP.
≥ The communication quality settings also depend on the settings on the
≥ The communication quality settings also depend on the settings on the
connected device. If the communication quality of the connected device is set
for stable communication, the quality of the audio will remain low even if this
unit is set to “MODE 2”.
for stable communication, the quality of the audio will remain low even if this
unit is set to “MODE 2”.
Others
Other Panasonic audio/video equipment may start functioning
when you operate the unit using the supplied remote control.
You can operate this unit in another mode by setting the remote
control operating mode to “REMOTE 2”.
The main unit and remote control must be set to the same
mode.
when you operate the unit using the supplied remote control.
You can operate this unit in another mode by setting the remote
control operating mode to “REMOTE 2”.
The main unit and remote control must be set to the same
mode.
1
Press [EXT-IN, RADIO] to select “AUX”.
2
Press and hold [RADIO/EXT-IN] on the main
unit and [2] on the remote control until the main
unit’s display shows “REMOTE 2”.
unit and [2] on the remote control until the main
unit’s display shows “REMOTE 2”.
3
Press and hold [OK] and [2] on the remote
control for at least 4 seconds.
control for at least 4 seconds.
To change the mode back to “REMOTE 1”, repeat the steps
above by replacing [2] with [1].
above by replacing [2] with [1].
When the following situations occur, reset the memory:
≥ There is no response when buttons are pressed.
≥ You want to clear and reset the memory contents.
≥ There is no response when buttons are pressed.
≥ You want to clear and reset the memory contents.
∫ To reset memory
1
Disconnect the AC power supply cord. (Wait for
at least 3 minutes before proceeding to step 2.)
at least 3 minutes before proceeding to step 2.)
2
While pressing and holding down [POWER, Í/
I] on the main unit, reconnect the AC power
supply cord.
supply cord.
“--------” appears on the display.
3
Release [POWER, Í/I].
All the settings are returned to the factory preset. You will
need to reset the memory items.
need to reset the memory items.
Disconnecting a Bluetooth
®
device
Advanced functions
MODE 1: Connection with emphasis on communication
stability
MODE 2: Connection with high bit rate for good audio quality
(Communication might easily be disconnected in
this mode, select “MODE 1” if this occurs).
this mode, select “MODE 1” if this occurs).
ON:
This unit will automatically select “BLUETOOTH”
when a Bluetooth
when a Bluetooth
®
device is connected.
OFF
Changing the main unit and
remote control mode
remote control mode
Memory reset (Initialization)
SC-HC55_35-RQTX1260.book 15 ページ ２０１１年４月４日 月曜日 午後４時５０分