Panasonic RQT9633-4P User Manual

RQT9633

You can preset up to 30 channels.
Preparation
Make sure that the FM antenna is connected. (> 8)

A station previously stored is overwritten when another 
station is stored in the same channel preset.

Press [RADIO] to select “FM”.

Press [PLAY MENU] repeatedly to select 
“A.PRESET” and then press [OK].

Press [3, 4] to select “LOWEST” or 
“CURRENT” and then press [OK].

LOWEST:
To begin auto preset with the lowest frequency 
(FM 87.9 or FM 87.5).
CURRENT:
To begin auto preset with the current 
frequency.*

* To change the frequency, refer to “Manual tuning and 

presetting”.

The tuner starts to preset all the stations it can 
receive into the channels in ascending order.

Preparation
1

Press [RADIO] to select “FM”.

2

Press [PLAY MENU] repeatedly to select 
“TUNEMODE” and then press [OK].

3

Press  [3, 4] to select “PRESET” and then 
press [OK].

Press [RADIO] to select “FM”.

Press [:/6] or [5/9] to select the 
channel.

∫ Manual tuning and presetting

Select a radio broadcast.
1

Press [RADIO] to select “FM”.

2

Press [PLAY MENU] repeatedly to select 
“TUNEMODE” and then press [OK].

3

Press  [3, 4] to select “MANUAL” and then 
press [OK].

4

Press  [:/6] or [5/9] to tune to the 
required station.

≥ To start automatic tuning, press and hold 

[:/6], [5/9] until the frequency starts 

scrolling. Tuning stops when a station is found.

To preset the channel
5

While listening to the radio broadcast
Press [OK].

6

Press  [3, 4] to select the channel and then 
press [OK].

∫ To improve FM sound quality

1

While receiving FM broadcasts, press 
[PLAY MENU] repeatedly to select “FM MODE” 
and then press [OK].

2

Press  [3, 4] to select “MONO” and then press 
[OK].

≥ This setting can be preset and memorized. To do 

so, continue to step 5 of “Manual tuning and 
presetting”.

≥ Select “STEREO” in step 2 to return to stereo 

broadcasts.

≥ “MONO” is canceled if the frequency is changed.
≥ If “MONO” is selected, regardless of the type of signal 

this unit is receiving, “FM MONO” is displayed when 
[DISPLAY] is pressed. (> below)

∫ To display the current signal status

Press [DISPLAY].

≥ “STEREO” is displayed when this unit tunes to a stereo 

broadcast.

This unit can output Internet radio if “vTuner for 
Panasonic” is installed on your iPhone/iPod touch.
Preparation
≥ Install “vTuner for Panasonic” to your iPhone/

iPod touch.

≥ Install iOS 5.0 or later.

Insert the iPhone/iPod touch to this unit.

Press [iPod] repeatedly to select “VTUNER”.

{.

“vTuner for Panasonic” starts.

≥ Visit the below website for the following information 

about “vTuner for Panasonic”:
http://radio.vtuner.com/panasonic/en/
(Compatible iPhone/iPod touch models and software 
versions, purchasing, installation and operation details.)

≥ A pop-up screen may appear on your iPhone/iPod 

touch. Follow the indicated instructions.

“FM ST”: The FM signal is in stereo.
“FM”:

The FM signal is in monaural.

≥ “FM” is also displayed even if this unit is not 

tuned to a station.

SC-HC37~RQT9633.book  10 ページ  ２０１２年２月２８日　火曜日　午後３時４３分