Panasonic SA-HE100 User Manual
12
RQT6208
Control guide
POWER
SPEAKERS
A
B
DOWN
DSP SOUND MODE
PHONES
- HELP
– RESET
– RESET
- BAND
– FM MODE MEMORY
– FM MODE MEMORY
ENHANCED SURROUND
TUNING
PRESET
NEO:6
DOLBY
PRO LOGIC
2
8
2
1
Standby/on button [POWER,
8
]
Press to switch the unit from on to standby mode or vice versa.
In standby mode, the unit is still consuming a small amount of power.
In standby mode, the unit is still consuming a small amount of power.
Speaker A/B select buttons [SPEAKERS, A, B]
Turning the speakers off automatically engages the STEREO mode
(when listening through headphones, for example).
If your speakers have an impedance under 6
(when listening through headphones, for example).
If your speakers have an impedance under 6
Ω
Press and hold [A] or [B] until “LOW IMP” lights up on the display.
Note that when “LOW IMP” is on, SPEAKERS A and B cannot be used
at the same time.
Note that when “LOW IMP” is on, SPEAKERS A and B cannot be used
at the same time.
Help/reset button [-HELP, –RESET]
Press if an error message appears. A message offering a possible
solution scrolls across the display.
To reinitiate the unit’s settings, press and hold until “RESET” appears.
solution scrolls across the display.
To reinitiate the unit’s settings, press and hold until “RESET” appears.
Memory button [MEMORY]
For presetting radio stations.
Headphone jack [PHONES]
Plug type: 6.3 mm (1/4") stereo
Avoid listening for prolonged periods of time to prevent hearing
damage.
Turn the speakers off when using the headphones.
Avoid listening for prolonged periods of time to prevent hearing
damage.
Turn the speakers off when using the headphones.
Tuning buttons [TUNING,
2
,
1
]
For tuning the radio and selecting preset stations.
Press and hold until the frequency starts scrolling to start automatic
tuning. Tuning stops when a station is found.
Tuning intervals: FM–0.2 MHz, AM–10 kHz
Press and hold until the frequency starts scrolling to start automatic
tuning. Tuning stops when a station is found.
Tuning intervals: FM–0.2 MHz, AM–10 kHz
Preset channel button [PRESET]
Press to allow preset station selection with [TUNING,
2
,
1
].
Band select/FM mode select button
[-BAND, –FM MODE]
[-BAND, –FM MODE]
For switching between AM and FM.
If reception is poor in FM, press and hold until “MONO” appears to
switch to monaural mode.
If reception is poor in FM, press and hold until “MONO” appears to
switch to monaural mode.
DSP sound mode selector
[DSP SOUND MODE]
[DSP SOUND MODE]
For selecting “STEREO”,
“SURROUND” or “SFC”.
“SURROUND” or “SFC”.
Dolby Pro Logic
2
2
mode select button
[DOLBY PRO LOGIC
2
2
]
Use when “
%
PRO LOGIC
2
” lights in the SURROUND mode.
NEO:6 mode select button [NEO:6]
Use when “NEO:6” lights in the ENHANCED SURROUND mode.
Enhanced surround mode
select button
[ENHANCED SURROUND]
select button
[ENHANCED SURROUND]
TUNED
STEREO
MONO
LOW IMP
SPEAKERS
SPEAKERS
ATT
kHz
MHz
PRO LOGIC
2
DIGITAL
SOUND MODE
STEREO SURROUND
SFC
SFC
L
C
R
SL
S
SB
SR LFE
PCM
FIX
M
A
B
ENHANCED
NEO:6
ES
OVER
DSP sound mode
indicators
[SOUND MODE, STEREO,
SURROUND, SFC,
indicators
[SOUND MODE, STEREO,
SURROUND, SFC,
]
Show the current DSP sound mode.
ENHANCED
Frequency unit indicators [kHz, MHz]
kHz: AM, or PCM sampling frequency
MHz: FM
MHz: FM
The display
Speaker indicators [LOW IMP, SPEAKERS
,
]
LOW IMP: You have switched to LOW IMP because you have
connected speakers with an impedance under 6
Ω
.
SPEAKERS
Å
: Sound is output from speakers connected to the
front A, surround, and center terminals.
SPEAKERS
ı
: Sound is output only from speakers connected to
the front B terminals.
SPEAKERS
Å ı
: Sound is output from speakers connected to
the front A and B terminals.
B
A
Radio indicators [TUNED, STEREO, MONO,
˜
]
TUNED: A station is tuned.
MONO: You have switched to monaural mode with [-BAND, –FM
MONO: You have switched to monaural mode with [-BAND, –FM
MODE] to improve reception.
STEREO: A stereo FM broadcast is tuned.
˜
:Lights during presetting.
General display
Shows the input mode, radio frequency, and other general
information.
information.
Input overload indicator [OVER]
Lights when input exceeds rated values.
Turn the A/D attenuator on if this occurs
frequently (
Turn the A/D attenuator on if this occurs
frequently (
\
page 14).
A/D attenuator indicator
[ATT]
[ATT]
Lights when the A/D attenuator is
working.
working.