ONKYO PR-SC5508 User Manual
88
En
You’ll need to enter a code for each component that you
want to control.
want to control.
Note
• The remote control codes provided are correct at the time of
printing, but are subject to change.
Onkyo components that are connected via
u are con-
trolled by pointing the remote controller at the AV control-
ler, not the component. This allows you to control
components that are out of view, in a rack, for example.
ler, not the component. This allows you to control
components that are out of view, in a rack, for example.
If you want to control an Onkyo component by pointing
the remote controller directly at it, or you want to control
an Onkyo component that’s not connected via
the remote controller directly at it, or you want to control
an Onkyo component that’s not connected via
u, use the
following remote control codes:
• BD/DVD
• BD/DVD
`
30627:
Onkyo DVD player without
u
• TV/CD
`
71817:
Onkyo CD player without
u
`
11807:
TV with
p
If you want to control an Onkyo component by pointing
the remote controller directly at it, use the following
remote control codes:
the remote controller directly at it, use the following
remote control codes:
`
32900:
Onkyo Blu-ray Disc player
`
32901:
Onkyo HD DVD player
`
70868:
Onkyo MD recorder without
u
`
71323:
Onkyo CD recorder without
u
`
82990:
Onkyo Dock without
u
Entering Remote Control Codes
1
Look up the appropriate remote control code in
the separate Remote Control Codes list.
The codes are organized by category (e.g., DVD
player, TV, etc.).
the separate Remote Control Codes list.
The codes are organized by category (e.g., DVD
player, TV, etc.).
2
While holding down
REMOTE MODE to which
you want to enter a code, press and hold down
DISPLAY (about 3 seconds).
The REMOTE MODE button lights.
DISPLAY (about 3 seconds).
The REMOTE MODE button lights.
Note
• Remote control codes cannot be entered for RECEIVER
and ZONE.
• Only TV remote control codes can be entered for TV.
• Except for RECEIVER, TV and ZONE, remote control
• Except for RECEIVER, TV and ZONE, remote control
codes from any category can be entered as REMOTE
MODE. However, these buttons also work as input selec-
tor buttons (
MODE. However, these buttons also work as input selec-
tor buttons (
26), so choose a REMOTE MODE that
corresponds with the input to which you connect your
component. For example, if you connect your CD player
to the CD input, choose TV/CD when entering its remote
control code.
component. For example, if you connect your CD player
to the CD input, choose TV/CD when entering its remote
control code.
3
Within 30 seconds, use the number buttons to
enter the 5-digit remote control code.
REMOTE MODE button flashes twice.
If the remote control code is not entered success-
fully, REMOTE MODE button will flash once
slowly.
enter the 5-digit remote control code.
REMOTE MODE button flashes twice.
If the remote control code is not entered success-
fully, REMOTE MODE button will flash once
slowly.
Remote Control Codes for Onkyo
Components Connected via
Components Connected via
u
1
Make sure the Onkyo component is connected
with an
with an
u cable and an analog audio cable
(RCA).
u Components” for
2
Enter the appropriate remote control code for
REMOTE MODE.
• BD/DVD
REMOTE MODE.
• BD/DVD
`
31612:
Onkyo DVD player with
u
• TAPE
`
42157:
Onkyo cassette tape deck with
u
• TV/CD
`
71327:
Onkyo CD player with
u
• PORT
`
81993:
Onkyo Dock with
u
See the previous section for how to enter remote
control codes.
control codes.
3
Press
REMOTE MODE, point the remote control-
ler at the AV controller, and operate the compo-
nent.
nent.