Panasonic SC-PMX100/SC-PMX100B User Manual

RQ

T999

5

To check this system’s IP address or the Wi-Fi MAC 

address.

Press [3, 4] to select “IP Addr.” or “MAC Addr.” 
and then press [OK].
The IP address or the MAC address is partially 
displayed.

Press [2, 1] on the remote control to show the 
rest of the IP address or the MAC address.

• Press [OK] to exit.
• The “ – ” displayed on the top or bottom left of the 

display indicate the first and last units respectively.

To reset the network settings.

Press [2, 1] to select “OK? Yes” and then press 
[OK].

• Wait for “Network Initializing” to stop scrolling.

• “WAC Mode” will be indicated on the display.

– “Method 1” of network setting method is available. 

(> 6)

– To exit “WAC Mode”, press [∫].

• This function does not affect the “Wireless LAN” setting.

Before requesting service, make the following checks. If 

you are in doubt about some of the check points, or if the 

solutions indicated do not solve the problem, consult 

your dealer for instructions.

(This site is in English only.)

• Examine that the battery is installed correctly.
Sound is distorted or no sound.

• Adjust the volume of the system.

• Switch off the system, determine and correct the 

cause, then switch the system on again. It can be 

caused by straining of the speakers through excessive 

volume or power, and when using the system in a hot 

environment.

• Ensure the speaker cables are connected correctly 

and securely. (> 4)

• An AC mains lead or fluorescent light is near the 

cables. Keep other appliances and cords away from 

the cables of this system.

• One of the unit’s safety devices may have been 

activated.

Reset the unit as follows:

1 Press [Í/I] on the unit to switch the unit to standby.

• If the unit does not switch to standby, press [Í/I] on 

the unit for approximately 10 seconds. The unit is 

forcibly switched to standby. Alternatively, disconnect 

the AC mains lead, wait for at least 3 minutes, then 

reconnect it.

2 Press [Í/I] on the unit to switch it on. If the unit still 

cannot be operated, consult the dealer.

• During “AUX” mode, when a device is connected to 

both the AUX IN terminals and the USB port, noise 

may be generated depending on the device. In this 

case, remove the USB cable from the USB port.

• You have not put in the disc correctly. Put it in correctly.

• Disc is dirty. Clean the disc.

• Replace the disc if it is scratched, warped, or 

non-standard.

• There is condensation. Let the system dry for 1 to 2 hours.

• Keep the antenna away from computers, TVs, other 

cables and cords.

• Use an outdoor antenna.

• Switch off the TV or move it away from the system.
If noise is excessive during FM reception.

• Change the audio to be output as monaural.

1 Press [RADIO MENU] repeatedly to select “FM Mode”.
2 Press [2, 1] to select “Mono” and then press [OK].

The sound becomes monaural.

• To cancel, select “Stereo” or change the frequency.

In normal circumstances, select “Stereo”.

• Check that the iPhone/iPad/iPod is connected 

properly.

• Connect the iPhone/iPad/iPod again or try to restart 

the iPhone/iPad/iPod.

• During standby mode, charging will not start from the 

USB cable connection. 

Turn this unit on and make sure the charging has 

started before turning this unit to standby mode.

• The battery of the iPhone/iPad/iPod is depleted. 

Charge the iPhone/iPad/iPod, and then operate again.

– When using the port, turn this unit on. Do not turn this 

unit off until the iPhone/iPad/iPod becomes operational.

Panasonic is constantly improving the system’s 

software to ensure that our customers are enjoying 

the latest technology. (> 17)

SC-PMX100-100B_EGEBGN-RQT9995-B.book  18 ページ  ２０１５年４月２０日　月曜日　午後３時４５分