Panasonic SC-RT50 User Manual

Page of 52
34
RQT8655
The radio
Preparation
pTurn off TV while using radio since noise may occur.
pPress [THEATER] to switch the remote control to operate this unit.
1
Press [FM/AM] to select the “FM” or “AM”.
2
Press [
] or [] to select the 
frequency of the required station.
TUNED: Displayed when a radio 
station is tuned.
ST:
Displayed when a stereo FM 
broadcast is being received.
Press and hold [
] or [] until the frequency starts scrolling 
to start automatic tuning. Tuning stops when a station is found.
3
Adjust the volume with [
A B VOLUME].
If noise is excessive
Press [FM MODE].
Each time you press the button:
FM: Changes between stereo and forced monaural.
AM: BP1 
BP2  BP3  BP4 (BPNBeat Proof)
$
Select between BP1 and BP4 that receives good reception. 
The FM mode is cancelled when you change the frequency.
FM frequency step
The step is factory-set to 0.2 MHz, but you can change it to receive 
broadcasts allocated 0.1-MHz steps.
1 Press [FM/AM] to select “FM”.
2 Press and hold [
w] on the main unit.
After a few seconds the display changes to show the current 
minimum frequency. Continue to hold the button down. The 
minimum frequency changes and the step is changed.
To return to the original step, repeat the above steps.
[Note]
Any FM/AM frequencies preset in channels will be changed by this 
procedure. Preset them again.
Preset channels to make selection simple.
Up to 30 stations can each be set in the FM and AM bands.
1
Press [FM/AM] to select the “FM” or “AM”.
2
Press [
] or [] to tune to the 
lowest frequency.
FM: 87.9 MHz or 87.5 MHz
AM: 520 kHz
3
Press and hold [ENTER].
Release the button when “AUTO FM” or “AUTO AM” is lit on 
the display.
The tuner presets all the stations it can receive into the 
channels in ascending order.
p“SET OK” is displayed when the stations are set. The last 
station to be set is then played.
pThe unit of display is MHz for FM radio and kHz for AM radio when 
the selector is in FM/AM mode.
p“ERROR” is displayed
Presetting was unsuccessful. Preset manually.
1
Tune to the station (
➡ left).
2
Press [ENTER].
3
While “MEMO” is flashing on the display
Press the numbered buttons or [
9 : CH]
to select a channel and press [ENTER].
e.g., “2”:
[0] 
➡ [2]
“12”: [1] 
➡ [2]
The station occupying a channel is erased if another station is preset 
in that channel.
1
Press [FM/AM] to select “FM” or “AM”.
2
Press the numbered buttons or 
[
9 : CH] to select the channel.
e.g., “2”:
[0] 
➡ [2]
“12”: [1] 
➡ [2]
[Note]
If there is nearby electrical interference during auto tuning the 
frequency may come to a halt without locating a channel. Turn off the 
power of the nearby electrical equipment.
Use FM outdoor antenna if radio reception is 
poor.
pDisconnect the FM indoor antenna.
pThe antenna should be installed by a competent technician.
[Note]
pDisconnect the outdoor antenna when the unit is not in use.
pDo not use the outdoor antenna during an electrical storm.
Manual tuning
SRD MUSIC 
Numbered
buttons
9:CH
THEATER
A B VOLUME
H.BASS
SRD ENH
SURROUND MUSIC
SFC/EQ
C. FOCUS,
FM MODE
SRD MUSIC
ENTER
A B VOLUME
9:CH
FM/AM
Preset tuning
Automatic presetting
Manual presetting
Selecting channels
75
j coaxial cable
(not included)
Antenna plug
(not included)
Back of 
the main unit
FM outdoor antenna 
(Using a television 
antenna)