Panasonic 744T User Manual
744T User Guide and Technical Information
30
firmware v. 1.04
Features and specifications are subject to change. Visit www.sounddevices.com for the latest documentation.
Recording
The largest, most easily accessed control on the 744T is its record key. Recording takes
priority over all activity except for disk formatting, disk speed tests, and fi le transfers. The 744T will
immediately enter record mode whenever the record key is pressed. When recording, the adjacent
red LED will illuminate to indicate that the unit is in record mode.
immediately enter record mode whenever the record key is pressed. When recording, the adjacent
red LED will illuminate to indicate that the unit is in record mode.
If no inputs are routed to tracks, recording cannot take place. Make certain that at least one record track is
assigned for recording.
assigned for recording.
While recording, the power, ff, rew, input, tone, and drive keys are disabled. Recording is stopped by
pressing and holding the STOP key. The Stop key must be held for at least 150 ms to end recording.
Although you can enter the setup menu during recording, menu items that will affect recording are
lined out in the menu list.
pressing and holding the STOP key. The Stop key must be held for at least 150 ms to end recording.
Although you can enter the setup menu during recording, menu items that will affect recording are
lined out in the menu list.
When using the recorded track monitor selection, there is a sample rate dependent delay in the signal. At
48 kHz sampling, the delay is approximately 12 seconds. This delay is due to the record buffering topol-
ogy. Audio can not be monitored until it has left the record buffer and written to the recording media.
48 kHz sampling, the delay is approximately 12 seconds. This delay is due to the record buffering topol-
ogy. Audio can not be monitored until it has left the record buffer and written to the recording media.
During recording, subsequent presses of the record key can perform one of three setup-menu-se-
lected actions:
lected actions:
• no action,
• new cue - cue markers are set within the fi le being written,
• new fi le - a new fi le is started with each press of the record key, the take counter is increased by
• new cue - cue markers are set within the fi le being written,
• new fi le - a new fi le is started with each press of the record key, the take counter is increased by
one.
When removing the CF from the 744T, always observe the amber activity LED for the CF medium. If it is
lit, wait until it goes out before removing the CF. If you remove the CF while the LED is lit, the fi le will be
corrupted and there is a possibility of FAT corruption as well.
lit, wait until it goes out before removing the CF. If you remove the CF while the LED is lit, the fi le will be
corrupted and there is a possibility of FAT corruption as well.
Playback
Just like a “tape recorder”, pressing play will begin fi le playback. The 744T has high-resolution play-
back circuitry and is appropriate for any reference audio application. Any fi le recorded by the 744T
can be played back, including all uncompressed audio fi les and MP3 fi le playback. In addition, fi les
copied to the storage mediums from a computer can be played back. This is useful when using the
744T as a high-resolution playback device.
back circuitry and is appropriate for any reference audio application. Any fi le recorded by the 744T
can be played back, including all uncompressed audio fi les and MP3 fi le playback. In addition, fi les
copied to the storage mediums from a computer can be played back. This is useful when using the
744T as a high-resolution playback device.
The 744T plays back the last recorded audio fi le unless another fi le is selected. There are two ways to
select another fi le for playback. To select another fi le in the current record directory, push either the
FastForward or reverse key to put the 744T in to play-stop mode. The fi lename display will begin
fl ashing and the FastForward and Reverse keys are used to step through fi les available in the current
record directory. To select a fi le in an alternate directory, press the HDD key to enter the media direc-
tories. Navigate to the appropriate directory. Select the fi le that to play back with the Multi-Function
Controller and press play.
select another fi le for playback. To select another fi le in the current record directory, push either the
FastForward or reverse key to put the 744T in to play-stop mode. The fi lename display will begin
fl ashing and the FastForward and Reverse keys are used to step through fi les available in the current
record directory. To select a fi le in an alternate directory, press the HDD key to enter the media direc-
tories. Navigate to the appropriate directory. Select the fi le that to play back with the Multi-Function
Controller and press play.
If the stop key is pressed while playing fi les from an alternate directory, the 744T will revert to the
current daily directory.
current daily directory.