Sony BDV-E2100 Owner's Manual
51
US
BDV-E6100/BDV-E4100/BDV-E3100/BDV-E2100
4-446-733-11(1)
D:\NORM'S JOB\SONY HA\SO120029\BDV-
E6100_4100_3100_E2100\4446733111_US (U2)\090SET.fm
E6100_4100_3100_E2100\4446733111_US (U2)\090SET.fm
masterpage: Right
Set
ting
s
s
an
d Ad
just
men
ts
x [System Information]
You can display the system’s software
version information and the MAC address.
You can display the system’s software
version information and the MAC address.
x [Software License Information]
You can display the Software License
Information.
You can display the Software License
Information.
[Network Settings]
x [Internet Settings]
Connect the system to the network
beforehand. For details, see “Step 3:
Preparing for Network Connection”
(page 21).
Connect the system to the network
beforehand. For details, see “Step 3:
Preparing for Network Connection”
(page 21).
[Wired Setup]: Select this when you
connect to a broadband router using a LAN
cable.
[Wireless Setup(built-in)]: Select this when
you use the built-in wireless LAN of the
system for wireless network connection.
connect to a broadband router using a LAN
cable.
[Wireless Setup(built-in)]: Select this when
you use the built-in wireless LAN of the
system for wireless network connection.
For further details, visit the following website and
check the FAQ:
http://www.sony.com/blurayhtsupport/
check the FAQ:
http://www.sony.com/blurayhtsupport/
x [Network Connection Status]
Displays the current network connection
status.
Displays the current network connection
status.
x [Network Connection
Diagnostics]
You can run the network diagnostic to
check if the network connection has been
made properly.
Diagnostics]
You can run the network diagnostic to
check if the network connection has been
made properly.
x [Connection Server Settings]
Sets whether or not to display the
connected DLNA server.
Sets whether or not to display the
connected DLNA server.
x [Renderer Options]
[Auto Access Permission]: Sets whether or
not to allow automatic access from a newly
detected DLNA controller.
[Smart Select]: Allows a Sony DLNA
controller to find the system as the target
equipment to operate by using the infrared
ray. You can set this function to on or off.
[Renderer Name]: Displays the system’s
name as it is listed on other DLNA devices
on the network.
[Auto Access Permission]: Sets whether or
not to allow automatic access from a newly
detected DLNA controller.
[Smart Select]: Allows a Sony DLNA
controller to find the system as the target
equipment to operate by using the infrared
ray. You can set this function to on or off.
[Renderer Name]: Displays the system’s
name as it is listed on other DLNA devices
on the network.
x [Renderer Access Control]
Sets whether or not to accept commands
from DLNA controllers.
Sets whether or not to accept commands
from DLNA controllers.
x [PARTY Auto Start]
[On]: Starts a PARTY or joins an existing
PARTY at the request of a networked
device compatible with the PARTY
STREAMING function.
[Off]: Off.
[On]: Starts a PARTY or joins an existing
PARTY at the request of a networked
device compatible with the PARTY
STREAMING function.
[Off]: Off.
x [Registered Remote Devices]
Displays a list of your registered remote
devices.
Displays a list of your registered remote
devices.
To use this function, be sure to perform the
software update (page 46).
software update (page 46).
x [Remote Start]
[On]: Allows turn on the system by a
device linked via network when the system
is in standby mode.
[Off]: The system cannot be turned on by a
device linked via network.
[On]: Allows turn on the system by a
device linked via network when the system
is in standby mode.
[Off]: The system cannot be turned on by a
device linked via network.
Tip
Note