Sony HVR-1500 User Manual
84
Menu Contents
Chapt
er
7
Men
u
s
i.LINK OUTPUT [> i.Link Out]: When playing a tape recorded
in HDV format, set the format output from the HDV/DV
connector.
connector.
Note
Before changing the setting, either temporarily disconnect the
i.LINK cable or power off the connected device.
i.LINK cable or power off the connected device.
*
HDV [>> HDV]: Output in HDV format.
DV (SP) [>> DV (SP)]: Down-convert and output in DV format.
DVCAM [>> DVCAM]: Down-convert and output in DVCAM
DVCAM [>> DVCAM]: Down-convert and output in DVCAM
format.
DOWN CONVERTER [>
Down Conv]: Select the
aspect ratio conversion
mode for HDV down-
conversion.
aspect ratio conversion
mode for HDV down-
conversion.
CONV MODE [>> D-Con
Mod]: Select conversion
mode.
mode.
SQUEEZE [>>> Squeeze]: Select the squeeze mode.
*
*
EDGE-CROP [>>> Edge Crp]: Select the edge crop mode.
CROP POSI [>> Crop Posi]:
Control crop position.
0 [>>> 0] to +B4 [>>> B4]
Factory default setting: *5A
Factory default setting: *5A
SDI H-ANC [> SDI H-ANC]:
Select whether to add
RP188 LTC and aspect
ratio data to the ancillary
data space of the SDSDI
output.
RP188 LTC and aspect
ratio data to the ancillary
data space of the SDSDI
output.
RP188LTC [>> RP188LTC]:
RP188 timecode
OFF [>>> OFF]: Do not embed an LTC signal.
*ON [>>> ON]: Output an embedded LTC signal.
*ON [>>> ON]: Output an embedded LTC signal.
ASPECT [>> ASPECT]:
Aspect ratio data
OFF [>>> OFF]: Do not embed aspect ratio data.
*ON [>>> ON]: Output embedded aspect ratio data.
*ON [>>> ON]: Output embedded aspect ratio data.
SYSTEM SEL [System Sel]: Settings related to system
selection
selection
Description of settings
Select system frequency to use.
*59.94i (UC) [> 59.94i UC]: For NTSC regions other than
Japan
59.94i (J) [> 59.94i J]: For Japan
50i (PAL) [> 50i PAL]: For PAL regions
50i (PAL) [> 50i PAL]: For PAL regions
Note
After changing the setting, press the POWER switch to power
off the unit, then press once more to restart. This changes the
initial settings of the entire setup menu to the new setting.
off the unit, then press once more to restart. This changes the
initial settings of the entire setup menu to the new setting.
SETUP BANK OPERATION [Setup Bank]: Settings related
to menu bank operations
to menu bank operations
Description of settings
Menu banks:
This unit allows four different complete sets of menu settings to be saved in what are termed “menu banks” numbered
1 to 4. Saved sets of menu settings can be recalled for use as required.
This unit allows four different complete sets of menu settings to be saved in what are termed “menu banks” numbered
1 to 4. Saved sets of menu settings can be recalled for use as required.
RECALL BANK1 [> Recall 1]: Recall menu settings from
menu bank 1.
(1) Select the bank you want to recall, then press the
,/B
button.
Message “RECALL OK?” appears.
Message “RECALL OK?” appears.
(2) To recall, press the SET (YES) button.
To quit recalling, press the RESET (NO) button.
RECALL BANK2 [> Recall 2]: Recall menu settings from
menu bank 2.
RECALL BANK3 [> Recall 3]: Recall menu settings from
menu bank 3.
RECALL BANK4 [> Recall 4]: Recall menu settings from
menu bank 4.
SAVE BANK 1 [> Save 1]: Save current menu settings to
menu bank 1.
(1) Select the bank you want to save, then press the
,/B
button.
Message “SAVE OK?” appears.
Message “SAVE OK?” appears.
(2) To save, press the SET (YES) button.
To quit saving, press the RESET (NO) button.
SAVE BANK 2 [> Save 2]: Save current menu settings to
menu bank 2.
SAVE BANK 3 [> Save 3]: Save current menu settings to
menu bank 3.
SAVE BANK 4 [> Save 4]: Save current menu settings to
menu bank 4.
INTERFACE SELECT [Interface]: Settings related to
external interfaces
external interfaces
Description of settings