Linear Car Stereo System Leaflet
IN
S
T
R
,A
M
-R
R
R
L
in
e
a
r
P
/N
:
2
1
2
0
4
5
B
M
a
te
ri
a
l:
2
0
L
b
.
M
e
a
d
B
o
n
d
S
iz
e
:
8
.5
0
0
"
x
1
1
.0
0
0
"
In
k
:
B
la
c
k
S
c
a
le
:
1
-1
S
id
e
1
o
f
2
AM-RRR
Remote
Radio
Receiver
Radio
Receiver
Installation
Instructions
Instructions
INTRODUCTION
The AM-RRR remote radio receiver is designed for use with Linear’s Model
AM/II access control system. The AM-RRR functions as a remote device that
extends the radio range or supplies localized radio reception for the AM/II.
AM/II access control system. The AM-RRR functions as a remote device that
extends the radio range or supplies localized radio reception for the AM/II.
Three antenna types can be used with this receiver. The cabinet mounted
type “F” connector is for connection to the antenna. The local whip antenna
(supplied) screws directly on to the receiver’s connector. The directional
(EXA-2000) and omni-directional (EXA-1000) remote antennas wire to the
receiver’s antenna connector with type RG-59 cable.
type “F” connector is for connection to the antenna. The local whip antenna
(supplied) screws directly on to the receiver’s connector. The directional
(EXA-2000) and omni-directional (EXA-1000) remote antennas wire to the
receiver’s antenna connector with type RG-59 cable.
An on-board RADIO RANGE knob allows adjustment of the receiver’s gain.
It can be set to limit the maximum radio range that the receiver can achieve.
Two indicators display the receivers performance and operation. The two color
red/green STATUS indicator lights red when the receiver is getting DC power
and turns green when access is granted to a transmitter. The RADIO indicator
lights when the receiver detects a radio signal. It can be used for trouble
shooting and verifying system performance. Receiver test points are provided
for listening to the incoming signals.
It can be set to limit the maximum radio range that the receiver can achieve.
Two indicators display the receivers performance and operation. The two color
red/green STATUS indicator lights red when the receiver is getting DC power
and turns green when access is granted to a transmitter. The RADIO indicator
lights when the receiver detects a radio signal. It can be used for trouble
shooting and verifying system performance. Receiver test points are provided
for listening to the incoming signals.
The AM-RRR remote radio receiver connects to the AM/II control unit through
a six-wire cable. A rotary switch in the AM-RRR selects the device address
for the receiver. Each remote device connected to the AM/II must be set to a
different device address. Power is supplied to the receiver from the AM/II.
a six-wire cable. A rotary switch in the AM-RRR selects the device address
for the receiver. Each remote device connected to the AM/II must be set to a
different device address. Power is supplied to the receiver from the AM/II.
The receiver is housed in a weather-resistant enclosure and can be mounted
indoors or outdoors. Gaskets and a weather-tight wiring strain relief seal the
unit from the elements.
indoors or outdoors. Gaskets and a weather-tight wiring strain relief seal the
unit from the elements.
1. TYPICAL INSTALLATION
2. OPEN CASE
3. LOCATE COMPONENTS
4. SET DEVICE ADDRESS
(760) 438-7000 • FAX (760) 438-7043
USA & Canada (800) 421-1587 & (800) 392-0123
Toll Free FAX (800) 468-1340
www.linearcorp.com
OPEN CASE FROM
ANTENNA END
ANTENNA END
REMOVE FOUR
SCREWS AND WASHERS
SCREWS AND WASHERS
BOARD SLIDES OUT
FROM 3RD SLOT UP
INSIDE CASE
FROM 3RD SLOT UP
INSIDE CASE
RADIO
RANGE
KNOB
RANGE
KNOB
CLOCKWISE
FOR MAXIMUM
GAIN
FOR MAXIMUM
GAIN
ANTENNA
CONNECTOR
(HIDDEN)
CONNECTOR
(HIDDEN)
DEVICE
ADDRESS
SELECTOR
ADDRESS
SELECTOR
POWER & DATA
TERMINALS
(CONNECTS TO AM/II)
TERMINALS
(CONNECTS TO AM/II)
STATUS
INDICATOR
RED = POWER
GREEN = ACCESS
INDICATOR
RED = POWER
GREEN = ACCESS
RADIO
INDICATOR
INDICATOR
RADIO
TEST
POINTS
TEST
POINTS
GND
AUDIO
SET TO POSITION 1-6
(MUST BE DIFFERENT
FROM ALL OTHER
REMOTE DEVICES)
(MUST BE DIFFERENT
FROM ALL OTHER
REMOTE DEVICES)
SET DEVICE
ADDRESS
SELECTOR
ADDRESS
SELECTOR
EACH AM-RRR EQUALS 4 LOAD UNITS
CABLE LENGTH FORMULA FOR EACH AM-RRR USED IN SYSTEM
CABLE RUN
CABLE TYPE
FORMULA
300 FEET MAXIMUM
BELDEN 9931 (24 AWG)
WEICO 9405 (20 AWG)
FEET x LOAD UNITS < 3,000 MAXIMUM
FEET x LOAD UNITS < 10,000 MAXIMUM
500 FEET MAXIMUM
AM-RRR MOUNTED
OUTSIDE BUILDING
OUTSIDE BUILDING
HOMERUN
WIRE EACH
AM-RRR
TO AM/II
WIRE EACH
AM-RRR
TO AM/II