Alpine iXA-W407 User Manual
35
-EN
Adjusting the Level
Touch [
] or [
] of Level, then adjust the HPF or LPF level.
Adjustable output level: –12 to 0 dB.
Adjusting the Slope
Touch [
] or [
] of Slope, then adjust the HPF or LPF slope.
Adjustable slope: FLAT
*
, –6 dB/oct., –12 dB/oct., –18 dB/oct.,
–24 dB/oct.
* FLAT can be set for the HIGH slope only when User’s is selected in
“Setting the Response Slope for the High Range Speaker (TW
Setup)” (page 32). Depending on the response characteristics of the
speaker, care should be taken when setting the response slope to
FLAT, as speaker damage may result. With this unit, a message is
displayed when the response slope for the high range speaker is set
to FLAT.
Setup)” (page 32). Depending on the response characteristics of the
speaker, care should be taken when setting the response slope to
FLAT, as speaker damage may result. With this unit, a message is
displayed when the response slope for the high range speaker is set
to FLAT.
5
Repeat steps 3 to 4 to make adjustment to the other
bands.
bands.
• While adjusting the X-Over, you should consider the frequency
response of the connected speakers.
• About the 2.2ch (3WAY)/4.2ch (FRONT/REAR/SUBW.) system
You can switch the system mode with the 2.2ch (3WAY)/4.2ch
(FRONT/REAR/SUBW.) switch on the PXA-H100. For details, refer
to the Owner’s Manual of PXA-H100.
(FRONT/REAR/SUBW.) switch on the PXA-H100. For details, refer
to the Owner’s Manual of PXA-H100.
Storing Settings in the Memory
Adjustment or setting contents of X-Over, T.Corr and P/G-EQ can be
stored.
Contents that can be stored vary depends on the audio processor used.
stored.
Contents that can be stored vary depends on the audio processor used.
1
Check whether the Defeat mode is OFF.
2
Touch [
] of PRESET on the A.Processor list
screen.
The preset station setting list is displayed.
3
Touch [MEMORY] of any preset stations
(1 through 6).
The setting contents are stored.
• The stored contents will not be deleted even when the battery power
cord is detached.
• This operation cannot be performed when a typical equalizer setting
(e.g. POPS) is selected in “Equalizer Presets (F-EQ)” (page 32).
Calling up the Preset Memory
1
Check whether the Defeat mode is OFF.
2
Touch [
] of PRESET on the A.Processor list
screen.
The preset station setting list is displayed.
3
Touch [
] of any preset stations (1 through 6) to
select the preset memory.
• It takes a few moments to call up the preset memory.
Setting the Subwoofer
1
Press and hold SETUP for at least 2 seconds.
The SETUP selection screen is displayed.
2
Touch [
] of Audio Setup.
The AUDIO SETUP screen appears.
3
Touch [
] or [
] of Subwoofer to set the subwoofer
ON/OFF.
4
Touch [
] of Subwoofer after setting the
Subwoofer to ON.
The SUBWOOFER Setup screen appears.
Setting items: Level / Phase / System / Channel
Touch [
] or [
] of Level to adjust the Subwoofer
output.
Setting range: 0 to 15
When the subwoofer is on, you can select either System1 or System2
for the desired subwoofer effect.
for the desired subwoofer effect.
Touch [
] or [
] of System to select SYSTEM1 or
SYSTEM2
Touch [
] or [
] of Phase to select 0° or 180°
The subwoofer output phase is toggled SUBWOOFER NORMAL (0°)
or SUBWOOFER REVERSE (180°).
or SUBWOOFER REVERSE (180°).
You can set the subwoofer output to stereo or monaural. Make sure to
set the correct output for your subwoofer type.
set the correct output for your subwoofer type.
Touch [
] or [
] of Channel to select STEREO or
MONO.
Adjusting the Subwoofer Level
Setting the Subwoofer System
SYSTEM1 : Subwoofer level changes according to the main
volume setting.
SYSTEM2 : Subwoofer level change is different from the main
volume setting. For example, even at low volume
settings, the subwoofer is still audible.
settings, the subwoofer is still audible.
Setting the Subwoofer Phase
Setting the Subwoofer Channel
STEREO: Subwoofer stereo (L/R) output
MONO:
Subwoofer monaural output