Intel Pentium 4 M RH80532GC029512 User Manual
Product codes
RH80532GC029512
Electrical Specifications
Mobile Intel
Pentium
4 Processor-M Datasheet
25
10.The specification is defined per PLL pin.
11. The voltage response to a processor current load step (transient) must stay within the Transient Voltage
Tolerance Window. The voltage surge or droop response measured in this window is typically on the order of
several hundred nanoseconds to several microseconds. The Transient Voltage Tolerance Window is defined
as follows:
several hundred nanoseconds to several microseconds. The Transient Voltage Tolerance Window is defined
as follows:
Case a) Load Current Step Up: e.g., from Icc = I_leakage to Icc = Icc_max. Allowable Vcc_min is defined as
minimum transient voltage at Icc = Icc_max for a period of time lasting several hundred nanoseconds to
several microseconds after the transient event.
minimum transient voltage at Icc = Icc_max for a period of time lasting several hundred nanoseconds to
several microseconds after the transient event.
Case b) Load Current Step Down: e.g., form Icc = Icc_max to Icc = I_leakage. Allowable Vcc_max is defined
as the maximum transient voltage at Icc = I_leakage for a period of time lasting several hundred
nanoseconds to several microseconds after the transient event.
as the maximum transient voltage at Icc = I_leakage for a period of time lasting several hundred
nanoseconds to several microseconds after the transient event.
12.This specification applies to both static and transient components. The rising edge of VCCVID must be
monotonic from 0 to 1.1 V. See
for current requirements. In this case, monotonic is defined as
continuously increasing with less than 50 mV of peak to peak noise for any width greater than 2 nS
superimposed on the rising edge.
superimposed on the rising edge.
Table 8. IMVP-III Voltage Regulator Tolerances for VID = 1.30 V Operating Mode (Maximum
Performance Mode)
I
CC
(A)
V
CC
Nominal
(V)
V
CC
Static Min
(V)
V
CC
Static Max
(V)
V
CC
Transient
Min (V)
V
CC
Transient
Max (V)
0.0
1.300
1.275
1.325
1.255
1.345
1.0
1.298
1.273
1.323
1.253
1.343
2.0
1.296
1.271
1.321
1.251
1.341
3.0
1.294
1.269
1.319
1.249
1.339
4.0
1.292
1.267
1.317
1.247
1.337
5.0
1.290
1.265
1.315
1.245
1.335
6.0
1.288
1.263
1.313
1.243
1.333
7.0
1.286
1.261
1.311
1.241
1.331
8.0
1.284
1.259
1.309
1.239
1.329
9.0
1.282
1.257
1.307
1.237
1.327
10.0
1.280
1.255
1.305
1.235
1.325
11.0
1.278
1.253
1.303
1.233
1.323
12.0
1.276
1.251
1.301
1.231
1.321
13.0
1.274
1.249
1.299
1.229
1.319
14.0
1.272
1.247
1.297
1.227
1.317
15.0
1.270
1.245
1.295
1.225
1.315
16.0
1.268
1.243
1.293
1.223
1.313
17.0
1.266
1.241
1.291
1.221
1.311
18.0
1.264
1.239
1.289
1.219
1.309
19.0
1.262
1.237
1.287
1.217
1.307
20.0
1.260
1.235
1.285
1.215
1.305
21.0
1.258
1.233
1.283
1.213
1.303
22.0
1.256
1.231
1.281
1.211
1.301
23.0
1.254
1.229
1.279
1.209
1.299
24.0
1.252
1.227
1.277
1.207
1.297