JL Audio SB-GM-CLREXT/10W3v3/TN2 User Manual
Specifications:
Enclosure Type: Sealed
Driver Type: 10W3v2-D2
Nominal Impedance: 4
Enclosure Type: Sealed
Driver Type: 10W3v2-D2
Nominal Impedance: 4
Ω
Cont. Power Handling: 300 Watts
JL Audio recommends using a high quality amplifier such as the JL Audio 250/1. The diagram below shows the recommended
crossover, infrasonic filter and equalizer settings for the 250/1 when being used to power your Stealthbox®.
crossover, infrasonic filter and equalizer settings for the 250/1 when being used to power your Stealthbox®.
Included Hardware:
4) 1/4” Flat Washer
4) 1/4” Split Lock Washer
2) 1/4”-20 x 1” Bolts
2) #6 x 30mm-1mm Hex Bolts
1) 3/8” Split Lock Washer
2) 3/8” Flat Washer
1) 3/8” Fender Washer
1) 3/8”-16 x 2” Tap Bolt
1) 3/8”-16 Hex Nut
3) 3/4”Lx3/4”ODx3/8”ID Spacers
2) 1”L x1”OD x3/8”ID Spacers
4) 1/4” Flat Washer
4) 1/4” Split Lock Washer
2) 1/4”-20 x 1” Bolts
2) #6 x 30mm-1mm Hex Bolts
1) 3/8” Split Lock Washer
2) 3/8” Flat Washer
1) 3/8” Fender Washer
1) 3/8”-16 x 2” Tap Bolt
1) 3/8”-16 Hex Nut
3) 3/4”Lx3/4”ODx3/8”ID Spacers
2) 1”L x1”OD x3/8”ID Spacers
10369 N. Commerce Pkwy, Miramar, Florida 33025-392 Phone: 954.443.1100 Fax: 954.443.1111
JL AUDIO 250/1
monoblock subwoofer amplifier
Amplifier Input Section
Input Sens.
Input Voltage
Low/High
Left Ch.
Right Ch.
Signal Sensing
Off/On
Output Mode
Full-Range/Low-Pass/High-Pass
Left Ch.
Right Ch.
Amp LP Filter
Mode/Slope
Off/12dB/24dB
Filter Freq. (Hz)
Bass Control
LF Boost (dB)
Off/30Hz
Infrasonic Filter
+1
+13
+3
+7
+10
Preamp Output Section
+12VDC
Ground
Remote
The JL Audio 250/1 is a very versatile audio component. Please consult the owner’s manual for detailed information
about installing and tuning this amplifier.
about installing and tuning this amplifier.
➔
➔
➔
STEP 13: Place a supplied 3/4”Lx3/4”ODx3/8”ID
spacer onto the thumb screw.
spacer onto the thumb screw.
Insert the thumb screw through the front of the
plastic jack cover.
plastic jack cover.
STEP 14: On the back side of the plastic jack
cover.
cover.
Place the remaining pair of 3/4”Lx3/4”OD,3/8”ID
spacers onto the thumb screw.
spacers onto the thumb screw.
STEP 15: Place the tire stops and jack back onto
the jack bracket.
the jack bracket.
Place the plastic jack cover over the jack assembly
and secure with the thumb screw.
and secure with the thumb screw.
➔
S B - G M - C L R E X T / 1 0 W 3 v 2 , J L AU D I O, I n c 2 0 0 5
S h e e t S K U # 0 1 1 1 9 5 R ev i s i o n 5 / 1 9 / 2 0 0 5
Pa g e 3
w w w . j l a u d i o . c o m
Mid/High Frequency Driver Information:
CONGRATULATIONS!
INSTALL COMPLETE.
INSTALL COMPLETE.
XR650-CSi
TR650-CXi
Front Location Driver Size:
6.5”
6.5”
Applicable JL Audio Products:
TR,VR,XR & ZR650-CSi
TR,VR,XR & ZR650-CSi
Rear Location Driver Size:
6.5”
6.5”
Applicable JL Audio Products:
TR,VT & XR650-CXi
TR,VT & XR650-CXi
Cont.
From
Previous
Page
Difficulty Of Installation: