JL Audio SB-N-ARMAD/10W6v2/DG2 User Manual
Specifications:
Enclosure Type: Sealed
Driver Type: 10W6v2-D4
Nominal Impedance: 2
Enclosure Type: Sealed
Driver Type: 10W6v2-D4
Nominal Impedance: 2
Ω
Cont. Power Handling: 400 Watts
JL Audio recommends using a high quality amplifier such as the JL Audio 500/1. The diagram below shows the recommended
crossover, infrasonic filter and equalizer settings for the 500/1 when being used to power your Stealthbox®.
crossover, infrasonic filter and equalizer settings for the 500/1 when being used to power your Stealthbox®.
Included Hardware:
2) 3/8-16x1 Hex Tap Bolt
3) 3/8” Split Lock Washer
5) 3/8” Flat Washer
1) 3/8” x 1-1/4” Fender Washer
1) 3/8”-16x2-1/4” Socket Cup Set Screw
3) 3/8”-16 Hex Nut
2) 3/8-16x1 Hex Tap Bolt
3) 3/8” Split Lock Washer
5) 3/8” Flat Washer
1) 3/8” x 1-1/4” Fender Washer
1) 3/8”-16x2-1/4” Socket Cup Set Screw
3) 3/8”-16 Hex Nut
10369 N. Commerce Pkwy, Miramar, Florida 33025-392 Phone: 954.443.1100 Fax: 954.443.1111
+12VDC
Remote
Ground
JL AUDIO 500/1
five-channel system amplifier
+
_
_
+
Subwoofer Output
MONO OUTPUT ONLY
40
45
55
65
85
120
200
Filter Freq. (Hz)
Mode / Slope
Off / 12dB / 24dB
Amp LP Filter
Infrasonic Freq. (Hz)
15
18
25
30
40
50
60
Off / 30Hz
Infrasonic Filter
0.5
0.7
1.1
1.6
2.7
4.3
"Q"
20
25
35
45
55
70
85
Center Freq.
0
+4
+10
+13
+15
Boost (dB)
Off / On
Bass EQ
Remote Bass Port
Advanced
Bass
Control
Bass
Control
Preamp Output Section
Full Range / Amp Filter / Out Filter
Output Mode
Filter Slope
12dB / 24dB
40
45
55
65
85
120
200
Filter Freq. (Hz)
Left Ch.
Right Ch.
Filter Mode
LP / HP
Amplifier Input Section
Input Sens.
Left Ch.
Right Ch.
Signal Sensing
Off / On
Input Voltage
Low / High
The JL Audio 500/1 is a very versatile audio component. Please consult the owner’s manual for detailed information
about installing and tuning this amplifier.
about installing and tuning this amplifier.
➔
➔
➔
STEALTHBOX WALL
THREADED INSERT
VEHICLE SHEET METAL
FENDER WASHER
SOCKET CUP SET SCREW
LOCK WASHER
FLAT WASHER
HEX NUT
STEP 25: Reach up through the removed vent
area from STEP 22. Place the supplied fender
washer, flat washer, lock washer and hex nut onto
the socket cup set screw.
area from STEP 22. Place the supplied fender
washer, flat washer, lock washer and hex nut onto
the socket cup set screw.
Again, through the removed vent area. Using a
15mm deep socket and long extension, secure the
mounting assembly to the slotted mounting bar.
15mm deep socket and long extension, secure the
mounting assembly to the slotted mounting bar.
Replace the vent.
STEP 26: Replace side carpet, cargo cleats, carpet-
ed storage flooring and floor storage door.
ed storage flooring and floor storage door.
STEP 27: Secure the jack with the pair of straps
that are found in the floor storage.
that are found in the floor storage.
➔
S B - N - A R M DA / 1 0 W 6 v 2 , J L AU D I O, I n c 2 0 0 5
S h e e t S K U # 0 1 1 1 9 3 R ev i s i o n 5 / 2 6 / 2 0 0 5
Pa g e 5
w w w . j l a u d i o . c o m
Mid/High Frequency Driver Information:
CONGRATULATIONS!
INSTALL COMPLETE.
INSTALL COMPLETE.
ZR650-CSi
XR650-CXi
Front Location Driver Size:
6.5”
6.5”
Applicable JL Audio Products:
TR,VR,XR & ZR650-CSi
TR,VR,XR & ZR650-CSi
Rear Location Driver Size:
6.5”
6.5”
Applicable JL Audio Products:
TR,VR & XR650-CXi
TR,VR & XR650-CXi
Cont.
From
Previous
Page
Difficulty Of Installation: