Earthquake Sound T2000WD/1 User Manual
6
7
T500W/2
Set Xover switch
to FULL
to FULL
K-10, ten-inch bass tube, in mono
application (4 Ohms minimum)
application (4 Ohms minimum)
7.0V
17.0V
4.0V
10.0V
2.5V
5.0V
1V
1V
The gain knob is not a volume
control. It is designed to match
the input level of the amp to the
output level of the source unit.
Over driving "clipping" the input
stage of the amp will cause
damage to the amplifier (please
refer to table for setting).
control. It is designed to match
the input level of the amp to the
output level of the source unit.
Over driving "clipping" the input
stage of the amp will cause
damage to the amplifier (please
refer to table for setting).
MAX INPUT
VOLTAGE
BEFORE
CLIPPING
RCA LEVEL
SPEAKER
LEVEL
250Hz
210Hz
170Hz
125Hz
90Hz
50Hz
XOVER
KNOB
SETTING
T500W/2
One
30A
fuse
30A
fuse
To car chassis / ground
To remote turn on / trigger
To battery positive (+)
Bridgeable Speaker
outputs, minimum
4-Ohms mono.
outputs, minimum
4-Ohms mono.
MODE SELECTOR:
This feature tells the
amplifier to run in
either HIGH PASS,
FULL RANGE or
LOW PASS MODE
This feature tells the
amplifier to run in
either HIGH PASS,
FULL RANGE or
LOW PASS MODE
LEVEL ADJUST:
Allows the amplifier to deliver a controlled
maximum sound level into selected
channel(s) when the volume is turned to
max. This acts as a volume limiter for the
system, preventing you from over driving
the speakers or subwoofers.
Allows the amplifier to deliver a controlled
maximum sound level into selected
channel(s) when the volume is turned to
max. This acts as a volume limiter for the
system, preventing you from over driving
the speakers or subwoofers.
LOW LEVEL INPUTS:
Low level inputs
range
Low level inputs
range
of 0.2V to 5V RMS.
This is where the front and
rear RCA outputs from your
head unit or other devices
are inserted.
rear RCA outputs from your
head unit or other devices
are inserted.
with a
R C A l i n e
t h r o u g h t o
c a s c a d e
a n o t h e r
amplifier.
N o X o v e r
point.
t h r o u g h t o
c a s c a d e
a n o t h e r
amplifier.
N o X o v e r
point.
2-WAY 12dB/Oct
VARIABLE XOVER:
C o n t r o l
VARIABLE XOVER:
C o n t r o l
t h e
corresponding channels
cutoff frequencies. This
feature is disabled when
in FULL RANGE
cutoff frequencies. This
feature is disabled when
in FULL RANGE
This information applies to
both HPF and LPF
FC6.2
FC6.2
FC6.2 Xover FC6.2 Xover
FC6.2 Midrange
FC6.2 Midrange
AUTO SIGNAL
SENSING:
Please refer to page 3 for
e x p l a n a t i o n o f t h i s
feature.
SENSING:
Please refer to page 3 for
e x p l a n a t i o n o f t h i s
feature.
HIGH LEVEL
INPUT:
Speaker level
inputs with a
range of 0.5V
to 17V RMS.
INPUT:
Speaker level
inputs with a
range of 0.5V
to 17V RMS.
BASS BOOST:
0 - 18dB Bass
Boost for use
w
0 - 18dB Bass
Boost for use
w
i
t
h
subwoofers.
AUTO ON
REMOTE ON
RESET
POWER LED:
When LED is on, it
indicates that the
amplifier is ON and
f u n c t i o n i n g
properly.
When LED is on, it
indicates that the
amplifier is ON and
f u n c t i o n i n g
properly.
PROTECTION (PROT) LED:
If LED comes on then you have an
issue that requires service. Turn
o ff t h e a m p l i f i e r a n d c a l l
Earthquake for further assistance.
See warranty for details.
If LED comes on then you have an
issue that requires service. Turn
o ff t h e a m p l i f i e r a n d c a l l
Earthquake for further assistance.
See warranty for details.
Specifications Are Subject To Change Without Notice
www.earthquakesound.com