Panasonic CQ-C1110W User Manual
Power Connector
Antenna
6
(Yellow)
Battery lead
To the car battery, continuous +12 V DC
To the car battery, continuous +12 V DC
External Power Amplifier
CY-M7052
(option)
CY-M7052
(option)
RCA Cord
(option)
(option)
System up
speakers
speakers
To remove the Fuse
Fuse (15 A)
(Red)
R (Red)
Power lead
To ACC power, +12 V DC
To ACC power, +12 V DC
(Dark blue/white stripe)
(Dark blue)
(Black)
Ground lead
To a clean, bare metallic
part of car chassis.
To a clean, bare metallic
part of car chassis.
(+)
(–)
(+)
(–)
(+)
(–)
(+)
(–)
Left speaker
(Front)
Right speaker
(Front)
(White)
L (White)
(Gray)
(Green)
(Violet)
(White/
black
stripe)
black
stripe)
(Green/black
stripe)
stripe)
(Violet/black
stripe)
stripe)
(Gray/black
stripe)
stripe)
FRONT SP
REAR SP
Left speaker
(Rear)
Right speaker
(Rear)
Speaker lead
Preamp output connector (rear)
R (Red)
CQ-C1110W/C1100W
Amp. relay control power lead
(Max. 500 mA)
This lead is for connection to the power
amplifier.
(Max. 500 mA)
This lead is for connection to the power
amplifier.
ACC
Motor antenna
relay control lead
(To motor antenna)
(Max. 500 mA)
This lead is not intended
for use with switch actuated
power antenna.
relay control lead
(To motor antenna)
(Max. 500 mA)
This lead is not intended
for use with switch actuated
power antenna.
Note: This lead is used for power
control when an external power
amplifier is connected. The power
supply of a power amplifier will be
activated when turning on the power of
this unit.
control when an external power
amplifier is connected. The power
supply of a power amplifier will be
activated when turning on the power of
this unit.
Note: The power antenna extends
automatically when turning on the
power of this unit.
automatically when turning on the
power of this unit.
BATTERY 15A
L (White)
C
1
3
2
Fuse
6
Power
connector
connector
Control power extension lead
(option )
(option )
R (Red)
L (White)
16
17
CQ-C1110W/C1100W
CQ-C1110W/C1100W
13
E
N
N
G
L
I
S
H
H
14
E
N
N
G
L
I
S
H
H
Electrical connections
Caution:
• This product is designed to operate with a 12 V DC, negative ground battery system.
• To prevent damage to the unit, be sure to follow the connection diagram below.
• Strip about 5mm of the lead ends for connection.
• Do not insert the power connector into the unit until the wiring is completed.
• Be sure to insulate any exposed wires from a possible short-circuit from the car chassis. Bundle all
• This product is designed to operate with a 12 V DC, negative ground battery system.
• To prevent damage to the unit, be sure to follow the connection diagram below.
• Strip about 5mm of the lead ends for connection.
• Do not insert the power connector into the unit until the wiring is completed.
• Be sure to insulate any exposed wires from a possible short-circuit from the car chassis. Bundle all
cables and keep cable terminals free from touching any metal parts.
• Remember, if your car has a drive computer or a navigation computer, the data of its memory may be
erased when the battery terminals are disconnected.
C
If the fuse (rear panel) blows fre-
quently, they may be something
wrong with the unit or wiring.
Consult your nearest Panasonic
Service center for service.
quently, they may be something
wrong with the unit or wiring.
Consult your nearest Panasonic
Service center for service.
Note:
•
Use the optional extension lead to extend
the Amp. relay control power lead if needed.
the Amp. relay control power lead if needed.
•
The extension lead should be soldered and
insulated with the vinyl tape.
insulated with the vinyl tape.