ONKYO TX-SR702 Operating Guide
50
First Time Setup—Continued
Speaker Level Calibration
Here you can adjust the level of each speaker with the
built-in test tone so that the volume of each speaker is the
same at the listening position.
built-in test tone so that the volume of each speaker is the
same at the listening position.
Notes:
• The speakers cannot be calibrated while the output of
• The speakers cannot be calibrated while the output of
the AV receiver is muted, while a pair of headphones
is connected, or when using the multichannel input.
is connected, or when using the multichannel input.
• Because the TX-SR702/702E supports THX, the
test tone is output at the standard level of 0 dB
(absolute volume setting 82). If you normally listen
at volume settings below this, be careful because
the test tone will be much louder.
(absolute volume setting 82). If you normally listen
at volume settings below this, be careful because
the test tone will be much louder.
Notes:
• This procedure can also be performed by using the
• This procedure can also be performed by using the
remote controller. First press the [TEST TONE] but-
ton to output the test tone. Use the [LEVEL–] and
[LEVEL+] buttons to set the volume, and use the [CH
SEL] button to select the speakers.
ton to output the test tone. Use the [LEVEL–] and
[LEVEL+] buttons to set the volume, and use the [CH
SEL] button to select the speakers.
1
Press the [RECEIVER] button fol-
lowed by the [SETUP] button.
The main menu appears onscreen.
lowed by the [SETUP] button.
The main menu appears onscreen.
2
Use the Up and Down [
]/[
]
buttons to select “2. Speaker
Setup,” and then press [ENTER].
The Speaker Setup menu appears.
Setup,” and then press [ENTER].
The Speaker Setup menu appears.
This setting is set automatically by the Automatic
Speaker Setup function (see page 39).
Speaker Setup function (see page 39).
1, 6
2–4
2, 3
1
RECEIVER
ENTER
ENTER
3
Use the Up and Down [
]/[
]
buttons to select “3. Level Cali-
bration,” and then press
[ENTER].
The Level Calibration menu appears
and the pink noise test tone is output by
the front left speaker.
bration,” and then press
[ENTER].
The Level Calibration menu appears
and the pink noise test tone is output by
the front left speaker.
Note:
Speakers that you set to No or None on
the Speaker Configuration page
(page 46) cannot be selected.
Speakers that you set to No or None on
the Speaker Configuration page
(page 46) cannot be selected.
4
Use the Up and Down [
]/[
]
buttons to select each speaker,
and use the Left and Right [
and use the Left and Right [
]/
[
] buttons to set the volume.
The volume can be adjusted from –12
to +12 dB in 1 dB steps (–15 to +12 dB
for the subwoofer).
to +12 dB in 1 dB steps (–15 to +12 dB
for the subwoofer).
5
Repeat step 4 until the volume of
the test tone from each speaker
is the same.
When using a handheld Sound Level
Meter, calibrate each loudspeaker
channel (Left, Center, Right, Right Sur-
round, Surround Back Right, Surround
Back Left, Left Surround, and Sub-
woofer) to 75 dB SPL at the listening
position, measured with C-weighting
and slow reading.
the test tone from each speaker
is the same.
When using a handheld Sound Level
Meter, calibrate each loudspeaker
channel (Left, Center, Right, Right Sur-
round, Surround Back Right, Surround
Back Left, Left Surround, and Sub-
woofer) to 75 dB SPL at the listening
position, measured with C-weighting
and slow reading.
6
Press the [SETUP] button.
The setup menu closes.
The setup menu closes.
ENTER
ENTER
Menu
------------------------
1.Initial Setup
2.Speaker Setup
2.Speaker Setup
Advanced Setup
3.Surround Setup
4.Audio Adjust
5.Listening Mode Preset
6.Preference
3.Surround Setup
4.Audio Adjust
5.Listening Mode Preset
6.Preference
Basic Setup
2.Speaker Setup
------------------------
2.Speaker Distance
3.Level Calibration
4.Equalizer Settings
3.Level Calibration
4.Equalizer Settings
1.Speaker Config
2-4.Equalizer Settings
------------------------
Left
a. 80Hz : 0dB
b. 250Hz : 0dB
c. 800Hz : 0dB
d.2.5kHz : 0dB
e. 8kHz : 0dB
Left
a. 80Hz : 0dB
b. 250Hz : 0dB
c. 800Hz : 0dB
d.2.5kHz : 0dB
e. 8kHz : 0dB
Use Settings :Manual
2-3.Level Calibration
------------------------
b.Center : 0dB
c.Rught : 0dB
d.Surr Right : 0dB
e.Surr Back R : 0dB
f.Surr Back L : 0dB
g.Surr Left : 0dB
h.Subwoofer : 0dB
c.Rught : 0dB
d.Surr Right : 0dB
e.Surr Back R : 0dB
f.Surr Back L : 0dB
g.Surr Left : 0dB
h.Subwoofer : 0dB
a.Left : 0dB
ENTER
4_Setup_En Page 50 Tuesday, September 7, 2004 2:06 PM