Milwaukee 9561 User Manual

This hoist is intended for general industrial use for lifting and
transporting freely suspended material loads within its rated
capacity.

MILWAUKEE cannot be responsible for applications

other than those for which 

MILWAUKEE equipment is

recommended. Prior to installation and operation, we caution
the user to review his application for abnormal environmental
or handling conditions and to observe the applicable
recommendations as follows:

Do not use the hoist in areas containing flammable vapors,
liquids, gases or any combustible dusts or fibers. Refer to
Article 500 of the National Electrical Code. Do not use this
hoist in highly corrosive, abrasive or wet environments. Do not
use this hoist in applications involving extended exposure to
ambient temperatures below -10°F or above 130°F.

This hoist is not recommended for use in lifting or transporting
hazardous loads or materials which could cause widespread
damage if dropped. The lifting of loads which could explode or
create chemical or radioactive contamination if dropped
requires fail-safe redundant supporting devices which are not
incorporated into this hoist.

This hoist is not recommended for use in the lifting of guided
loads, including dumbwaiters and elevators. Such applications
require additional protective devices which are not
incorporated into this hoist. For such applications, refer to the
requirements of applicable state and local codes, and the
American National Safety Code for elevators, dumbwaiters,
escalators and moving walks (ASME A17.1).

1. Follow all local electrical and safety codes, as well as the

National Electrical Code (NEC) and the Occupational
Safety and Health Act (OSHA) in the United States.

2. Hoist must be securely and adequately grounded. The hoist

power cable is provided with an additional lead (green) for
grounding purposes.

3. Be careful when touching the exterior of an operating

motor; it may be hot enough to be painful or cause injury.
With modern motors this condition is normal if operated at
rated load and voltage (modern motors are built to operate
at higher temperatures).

4. Protect the power cable and control cable from coming in

contact with sharp objects.

5. Do not kink power cable and control cable and never allow

the cable to come in contact with oil, grease, hot surfaces,
or chemicals.

6. Make certain that the power source conforms to the

requirements of your equipment.

7. Inspect the unit daily before operating hoist.

8. Cluttered areas and benches invite accidents.

9. The operator should not engage in any practice which will

divert his attention while operating the hoist.

10. Before using the hoist, the operator should be certain that

all personnel are clear.

11. Do not operate hoist with loads exceeding its rated capacity.

12. Supporting frames or beams used as a hoist hanger must

have a greater load capacity than the hoist.

13. Do not attempt to operate hoist beyond normal maximum

lift range.

14. Align hoist for a straight line pull. Avoid side pull or end pull.

15. Do not operate hoist with twisted or damaged chain.

16. Do not operate a damaged or malfunctioning hoist until

necessary adjustments or repairs have been made.

17. Do not use hoist to lift people or to carry loads over people.

18. Do not leave a load suspended in the air unattended.

19. Always remove load before making repairs.

20. Do not remove or obscure capacity or warning decals.

1. Before installing the hoist, check the following:

a. Make sure all supporting structures and attaching devices

are strong enough to hold your intended loads. If in doubt,
consult a qualified structural engineer.

b. Provide proper branch circuit protection for the hoist as

recommended in the National Electrical Code.

c. The power supply should be within plus or minus 10% of

the voltage specified on the motor nameplate. It is critical
to use adequate sized power cables, especially with 
1-phase hoists (See Table 3). Be sure dual voltage hoists
are connected or wired to correspond with your power
supply (See WIRING, page 9).

d. Installation area must provide operating conditions for the

operator including sufficient room for the operator and
other personnel to stand clear of the load at all times.

e. For installations where the slack chain hanging from the

unit may be objectionable or hazardous, the use of a
chain container is recommended. See INSTALLATION OF
CHAIN CONTAINER ASSEMBLY.

Milwaukee Electric Tool Corporation
13135 West Lisbon Road
Brookfield, Wisconsin 53005
TEL: (800) 729-3878