Panasonic CY-VHD9500U User Manual
86
CY-VHD9500U
CY-VHD9500U
87
Troubleshooting
E
N
N
G
L
I
S
H
H
43
Preliminary Steps
Check and take steps as described in the tables below.
If You Suspect Something Wrong
Immediately switch the power off.
Disconnect the power connector and check that there is neither smoke nor heat from the unit before asking for
repairs. Never try to repair the unit by yourself because it is dangerous to do so.
Disconnect the power connector and check that there is neither smoke nor heat from the unit before asking for
repairs. Never try to repair the unit by yourself because it is dangerous to do so.
WARNING:
≥ Do not use the product when it is broken or there is some abnormality.
≥ Do not use the product when it is broken or there is some abnormality.
In the unlikely event that the product breaks (such as when no image is displayed or there is no sound)
or there is some abnormality (such as when a foreign object is inside the product, water was spilled
on it, smoke comes out or the product makes a strange smell), immediately stop using the product and
be sure to contact the store from which you purchased your product or a nearby Panasonic Servicenter.
Continuing to use the product in that condition could cause accidents, fi re or electrical shock.
or there is some abnormality (such as when a foreign object is inside the product, water was spilled
on it, smoke comes out or the product makes a strange smell), immediately stop using the product and
be sure to contact the store from which you purchased your product or a nearby Panasonic Servicenter.
Continuing to use the product in that condition could cause accidents, fi re or electrical shock.
Troubleshooting Tips
Common
No power to the unit.
The power cord (battery, ACC and
ground) is connected in the wrong
way.
ground) is connected in the wrong
way.
Check the wiring.
Fuse blow out.
Eliminate the cause of fuse blow out
and replace the fuse with new one.
Consult your dealer.
and replace the fuse with new one.
Consult your dealer.
Problem
Possible cause
Possible solution
Sound is not
generated.
generated.
The volume on the headphones is
adjusted to zero.
adjusted to zero.
Raise the volume on the headphones.
Cables are not correctly connected. Connect cables correctly.
MAIN POWER switch is set to OFF.
Switch MAIN POWER to ON.
The power of headphones is set to
OFF.
OFF.
Switch the power of headphones to
ON.
ON.
E
N
N
G
L
I
S
H
H
44
Problem
Possible cause
Possible solution
Noise
There is an electromagnetic-wave
generator such as a cellular phone
near the unit or its electrical lines.
generator such as a cellular phone
near the unit or its electrical lines.
Keep an electromagnetic-wave
generator such as a cellular phone
away from the unit and the wiring of
the unit. In case the noise cannot be
eliminated due to the wiring harness
of the car, consult your dealer.
generator such as a cellular phone
away from the unit and the wiring of
the unit. In case the noise cannot be
eliminated due to the wiring harness
of the car, consult your dealer.
The contact of the ground lead is
poor.
poor.
Make sure that the ground lead is
securely connected to an unpainted
part of the chassis.
securely connected to an unpainted
part of the chassis.
The headphones are too far from
this unit.
this unit.
Use the headphones within a distance
of 2.5 m from the unit.
of 2.5 m from the unit.
The path between the unit and
headphones is obstructed by
something.
headphones is obstructed by
something.
The batteries of the IR wireless
headphones have run down.
headphones have run down.
When using the headphones, remove
any obstacles that obstruct the path
between the headphones and unit.
any obstacles that obstruct the path
between the headphones and unit.
Replace the batteries.
Common (continued)
Monitor
The tilt angle or
the lateral angle of
the display is not
adjustable.
the lateral angle of
the display is not
adjustable.
There is an obstacle.
Install the unit where the unit moves
freely.
freely.
Problem
Possible cause
Possible solution
Noise is made in
step with engine
revolutions.
step with engine
revolutions.
Alternator noise comes from the
car.
car.
Change the wiring position of the
ground lead.
ground lead.
Mount a noise fi lter on the power supply.
Dome light
Dome lights do not
come on.
come on.
The wires are not connected
properly.
properly.
For the wiring connections of the dome
lights, consult a specialized contractor
or your dealer where you purchased
the unit.
lights, consult a specialized contractor
or your dealer where you purchased
the unit.
Problem
Possible cause
Possible solution
The dome light switch is at the OFF
position.
position.
Set it to the ON position.
The batteries of the IR wireless
headphones have run down.
headphones have run down.
Replace the batteries.